Siemens SIMOTION TB30 Скачать руководство пользователя страница 93

Страница: 93 / 150

Supplementary system components

6.2 Fan/battery module

SIMOTION D4x5-2
Manual, 02/2012

6.2

Fan/battery module

6.2.1

Cooling the SIMOTION D4x5-2 and backing up the real-time clock

Functions of a fan/battery module

The fan/battery module has the following tasks:
●

CPU cooling

●

Backing up the real-time clock if the SuperCap is insufficient.

The Control Unit monitors the temperature and the functioning of the fan.

Cooling the SIMOTION D4x5-2

A fan/battery module is always required for cooling the SIMOTION D4x5-2 Control Unit.

Table 6- 2

Fan/battery module for SIMOTION D4x5-2

Property

SIMOTION D425-2 DP
SIMOTION D435-2 DP/PN

SIMOTION D435-2 DP
SIMOTION D435-2 DP/PN

SIMOTION D445-2 DP/PN
SIMOTION D455-2 DP/PN

Fan/battery module

Always required (double fan/battery module included in the scope of supply)

Usable fan/battery

modules

Double fan/battery module, 6FC5348-0AA02-0AA0

Max. permissible

supply air temperature

55°C

Fan control

Temperature-controlled fan unit

will be switched on depending on supply air temperature and CPU load

The double fan/battery module guarantees sufficient cooling even with just one functional

fan.

Note
Use of the fan/battery module with single fan (order no. 6FC5348-0AA01-0AA0) on the

D4x5-2 is not possible.

An entry is made in the diagnostics buffer when a fan fault occurs (failure of one or both fans

in the double fan/battery module). The fan failure is also signaled by the generation of an

event in the PeripheralFaultTask and via a system variable.
If only one of the fans fails, the remaining fan continues under full load.
If both fans fail or with overtemperature, the controller switches to the RESET state, whereby

the SF LED flashes red/yellow (2 Hz) and the 7-segment display shows the state "8".

Содержание SIMOTION TB30























































































































































Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды

Siemens SIMOTION TB30, Руководство пользователя

Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды