Siemens SIMOTION TB30 Скачать руководство пользователя страница 54

Страница: 54 / 150

Interfaces

3.3 Ethernet interfaces

SIMOTION D4x5-2

Manual, 02/2012

Interface characteristics

Table 3- 5

X127 P1 and X130 P1 (X120 P1 only for SIMOTION D4x5-2 DP)

Characteristic

Type

Connector type

RJ45 socket connector

Cable type

Industrial Ethernet cable

•

4- and 8-wire cables can be used for 10/100 Mbit/s

•

8-wire cables must be used for 1000 Mbit/s

Max. cable length

100 m

Autocrossing

Yes

Dust protection blanking plugs for

sealing unused Ethernet ports

Five blanking plugs contained in the D4x5-2 scope of delivery

Blanking plugs (50 pcs) order number: 6SL3 066-4CA00-0AA0

Miscellaneous

X127 P1, X120 P1 and X130 P1 are full-duplex 10/100/1000 Mbit/s Ethernet ports

Pin assignment

Table 3- 6

X127 P1 and X130 P1 Ethernet interfaces (X120 P1 only for SIMOTION D4x5-2 DP)

Assignment in 10/100 Mbit mode

Assignment in 1 Gbit mode

Representation Pin

Signal

name

Signal type

Meaning

Signal

name

Signal type Meaning

TXP

Ethernet transmit

differential signal

DA+

Bidirectional pair A+

TXN

Ethernet transmit

differential signal

DA-

Bidirectional pair A-

RXP

Ethernet receive

differential signal

DB+

Bidirectional pair B+

- - -

Reserved, do not use DC+

Bidirectional pair C+

- - -

Reserved, do not use DC

Bidirectional pair C-

RXN

Ethernet receive

differential signal

DB-

Bidirectional pair B-

- - -

Reserved, do not use DD+

Bidirectional pair D+

- - -

Reserved, do not use DD-

Bidirectional pair D-

I = Input; O = Output; B = Bidirectional

Autocrossing functionality (if required, transmit and receive lines switch over)

Note
The MAC addresses are imprinted on an adhesive label that is located behind the protective

cover and can be seen from the front.

Содержание SIMOTION TB30























































































































































Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды

Siemens SIMOTION TB30, Руководство пользователя

Результаты поиска

Содержание SIMOTION TB30

Отзывы:

Похожие инструкции для SIMOTION TB30

Бренды по названию

Популярные бренды