Siemens SIMOTICS SD SH 71 315 Series Скачать руководство пользователя страница 68

Страница: 68 / 132

Electrical connection

6.5 Connecting a temperature sensor/anti-condensation heater

1LE7 shaft heights 71 ... 315

Operating Instructions, 04/2022, A5E51689275A-AA

Internal ground terminal

When making connections, ensure the following:
•

Ensure that the connecting surface is bare and is protected against corrosion using a

suitable substance, e.g. acid-free Vaseline.

•

Arrange the flat washer and spring washer under the bolt head.

•

Locate the cable lug under the clamping bracket.

•

Use the terminals designated for the grounding conductor in the terminal box.

•

Observe the tightening torque for the locking screw.

External ground terminal

When making connections, ensure the following:
•

Ensure that the connecting surface is bare and is protected against corrosion using a

suitable substance, e.g. acid-free Vaseline.

•

Position the cable lug between the contact bracket and the grounding bracket; do not

remove the contact bracket pressed into the enclosure!

•

Arrange the flat washer and spring washer under the bolt head.

•

Use the marked connection location for the grounding conductor on the stator housing.

•

Observe the tightening torque for the locking screw.

6.5

Connecting a temperature sensor/anti-condensation heater

WARNING

Hazard due to electric shock

The installation of the temperature sensors for the winding monitoring with respect to the

winding is implemented according to the requirements for basic insulation. The

temperature sensor connections are located in terminal boxes, safe to touch, and have no

protective separation. This is the reason that in the case of a fault, a hazardous voltage can

be present at the measuring sensor cable. When touched, this can result in death, severe

bodily injury and material damage.
•

When connecting the temperature sensor to external temperature monitoring devices,

when required, apply additional measures to fully comply with the requirements set out

in IEC 60664-1 or IEC 61800-5-1 "Hazard due to electric shock".

Содержание SIMOTICS SD SH 71 315 Series





































































































































Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды

Siemens SIMOTICS SD SH 71 315 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды