Siemens SIMOTICS SD SH 71 315 Series Скачать руководство пользователя страница 28

Страница: 28 / 132

Preparing for use

4.4 Delivery

1LE7 shaft heights 71 ... 315

Operating Instructions, 04/2022, A5E51689275A-AA

4.4

Delivery

Checking the delivery for completeness

The drive systems are put together on an individual basis. When you take receipt of the

delivery, please check immediately whether the items delivered are in accordance with the

accompanying documents. Siemens will not accept any claims relating to items missing from

the delivery and which are submitted at a later date.
•

Report any apparent transport damage to the delivery agent immediately.

•

Report any apparent defects/missing components to the appropriate SIEMENS office

immediately.

Archive the safety and commissioning notes provided in the scope of delivery as well as the

optionally available operating instructions so that these documents are always easily

accessible.
The rating plate optionally enclosed as a loose item with the delivery is provided to enable

the motor data to be attached on or near the motor or installation.

4.5

Transport and storage

4.5.1

Safety instructions for transport

Observe the following when carrying out any work on the motor:
•

Comply with the general safety instructions (Page 11).

•

Comply with the applicable national and sector-specific regulations.

•

When using the motor within the European Union, comply with the specifications laid

down in EN 50110-1 regarding safe operation of electrical equipment.

The information required to correctly attach, lift and transport the motor - such as weight,

center of gravity and attachment points - is provided here:
•

Motor dimension drawing and the associated explanations or the technical data

•

Transport data

•

Rating plate and lifting plate, if available

•

Shipping parts list

•

Packaging

Содержание SIMOTICS SD SH 71 315 Series





































































































































Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды

Siemens SIMOTICS SD SH 71 315 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды