Siemens SIMOTICS SD SH 71 315 Series Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 132

background image

Electrical connection

6.4 Connecting the grounding conductor

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA

65

6.3.3

Tightening torques

Note the information in Chapter "Tightening torques (Page 119)".

Cable entries, sealing plugs and thread adapters

Note the following when mounting:
•

Avoid damaging the cable jacket.

•

Adapt the tightening torques to the cable jacket materials.

Observe the documentation for tightening torques of the cable entries and sealing plugs for

direct mounting at the motor as well as additional glands (e.g. adapters).

6.4

Connecting the grounding conductor

The motor's grounding conductor cross-section must comply with EN / IEC 60034-1.
Please also observe installation regulations such as those specified in EN / IEC 60204-1.
Basically, there are two ways of connecting a grounding conductor to the motor.
•

Internal grounding with a connection in terminal box at the location intended for this

purpose and marked accordingly.

•

External grounding with connection at the stator housing at the locations intended for

this purpose and marked accordingly.

Type of enclosure grounding

Conductor cross-section

mm²

Connection of an individual conductor under

the external grounding bracket.

… 10

Connection is made using a DIN cable lug under

the external grounding bracket. DIN 46 234

… 25

Table 6- 3

Minimum cross-sectional area of grounding conductor

Minimum cross-section of the phase conductor

for installation

S

[mm²]

Minimum cross-section of the associated

grounding connection

[mm²]

S ≤ 25

S

25 < S ≤ 50

25

S > 50

0.5 S

«
...
65
66
67
68
69
...
»

Содержание SIMOTICS SD SH 71 315 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренд: VEM Страницы: 16

Бренд: GAS GAS Страницы: 71

Xcelorin LOSB9400 3.5T

Бренд: Team Losi Страницы: 4

Бренд: TAARKS Страницы: 7

Бренд: RADEMACHER Страницы: 60

Бренд: WPT POWER Страницы: 39

LOMBARDINI 9 LD 625-2

Бренд: Kohler Страницы: 92

Бренд: Fireye Страницы: 8

RADIOMODULE 2G4

Бренд: Grundfos Страницы: 76

Бренд: Wood-mizer Страницы: 36

Бренд: Honda Страницы: 59

Бренд: Dertec Страницы: 2

Бренд: Ingersoll-Rand Страницы: 42

Бренд: STEYR Страницы: 118

Бренд: O.S. engine Страницы: 40

Бренд: Hydro-Gear Страницы: 24

Бренд: Cuyuna Страницы: 51

Бренд: WÄRTSILÄ Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды