Siemens SIMOTICS SD SH 71 315 Series Скачать руководство пользователя страница 55

Страница: 55 / 132

Installation

5.4 Installing the motor

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA

5.4.2.4

Vertical types of construction with flange

The standard flange is provided with a centering. The choice of fit for the mating flange on

the driven machine is the system manufacturer's or the plant operator's responsibility.
If the motor is not fitted with a standard flange, align the motor to suit the driven machine.

Procedure

The motor axis must be vertical when it is lifted and the flange must be parallel to the mating

flange, so as to avoid seizing and stressing. Otherwise damage to the centering will result.
1.

Grease the centering flange with assembly paste to make the process easier.

Screw in two studs into tapped holes on opposite sides of the driven machine flange. The

studs act as positioning aids.

Lower the motor slowly toward the driven machine and into the centering, so that the

flanges do not quite touch. Lowering too quickly risks damaging the centering.

If necessary, rotate the motor into the right position so that the clearance holes in the flange

are central to the tapped holes.

Lower the motor completely onto the mating flange so that it is fully in contact; then

remove the studs.

Fix the motor using the flange fixing bolts.

5.4.3

Removing the rotor shipping brace

If a rotor shipping brace is attached to the motor, remove it at the last possible moment,

for example, when you are ready to push on the output or drive element.

Storing the rotor locking device

Store the rotor locking device in a safe place. It must be remounted if the motor is removed

and shipped on further.

5.4.4

Recommended alignment accuracy

The alignment accuracy required depends essentially on the configuration of the overall

machine train. Observe the required alignment accuracy of the coupling manufacturer in all

cases when aligning the motor.

Table 5- 1

Recommended alignment accuracy

Speed

rpm

Parallel offset

Angular offset

mm per 100 mm coupling diameter

750

0.09

1500

0.06

0.05

3000

0.03

0.025

Содержание SIMOTICS SD SH 71 315 Series





































































































































Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды

Siemens SIMOTICS SD SH 71 315 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды