Siemens SIMOTICS SD SH 71 315 Series Скачать руководство пользователя страница 18

Страница: 18 / 132

Safety information

2.10 Interference voltages when operating the converter

1LE7 shaft heights 71 ... 315

Operating Instructions, 04/2022, A5E51689275A-AA

2.10

Interference voltages when operating the converter

When a converter is in operation, the emitted interference varies in strength depending on

the converter (manufacturer, type, interference suppression measures undertaken). On

motors with integrated sensors (e.g. PTC thermistors), interference voltages caused by the

converter may occur on the sensor lead. This can cause faults which can result in eventual or

immediate death, serious injury or material damage.
•

Comply with the EMC information provided by the manufacturer of the converter. This is

how you prevent the limit values stipulated by IEC/EN 61000-6-2 .... IEC/EN 61000-6-4 for

the drive system (consisting of the motor and converter) from being exceeded.

•

You must put appropriate EMC measures in place.

2.11

Special designs and construction versions

Before carry out any work on the motor, determine the motor version.
If there are any deviations or uncertainty, contact the manufacturer, specifying the type

designation and serial number (see the rating plate), or contact the Service Center.

Содержание SIMOTICS SD SH 71 315 Series





































































































































Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды

Siemens SIMOTICS SD SH 71 315 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды