Siemens SIMOTICS SD SH 71 315 Series Скачать руководство пользователя страница 105

Страница: 105 / 132

Maintenance

9.3 Corrective maintenance

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA

103

Metal fan

•

Shaft heights 71...90: Release the M5 set screw so that the fan can rotate freely on the

shaft.

•

Shaft height 100...315: Remove the locking ring.

•

Use a suitable tool to pull off the fan (puller).

•

Locate the arms of the pulling tool in the openings in the fan in the vicinity of the hub.

•

Alternatively, place the pulling tool at the outer edge of the fan plate.

•

Uniformly withdraw the fan from the shaft by turning the pressure screw of the pulling

tool.

•

Do not apply any hammer blows to avoid damaging the rotor shaft, the fan and the

bearings.

•

Order the appropriate new parts if damaged.

Canopy

Canopies with spacer bolts or with screwed mounting brackets

Forcibly removing or separating can destroy the distance bolts, the connecting elements of

the mounting bracket or the fan cover.
•

Release the fixing screw on the outer surface of the canopy.

•

Under no circumstances remove the spacer bolts or the mounting bracket – or forcibly

separate them from one another or the cover.

Canopies with welded support brackets

•

Release the fixing screws at the contact location (canopy foot - riveting nut) at the outer

surface of the cover mesh.

9.3.4

Canopy, encoder under the canopy

•

For screwed canopies, insert the fastening screws through the holes on the outer surface

of the canopy. Tighten the fastening screws with a torque of 3 Nm ± 10 %.

Содержание SIMOTICS SD SH 71 315 Series





































































































































Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды

Siemens SIMOTICS SD SH 71 315 Series, Руководство по эксплуатации

Результаты поиска

Содержание SIMOTICS SD SH 71 315 Series

Отзывы:

Похожие инструкции для SIMOTICS SD SH 71 315 Series

Бренды по названию

Популярные бренды