Siemens SIMATIC S7-1200 CP 1243-8 IRC Скачать руководство пользователя страница 82

Страница: 82 / 230

Configuration

4.9 Serial interface

CP 1243-8 IRC

Operating Instructions, 02/2018, C79000-G8976-C385-03

4.9.4

WAN parameters (networking the CP)

Interfaces of the CP

The following figure shows both interfaces of the CP in the STEP 7 device icon (network

view):

X1
X2

Ethernet interface
Serial interface

Figure 4-1

Device icon of the CP with interface numbers

Networking interfaces

To network an interface depending on the initial situation you have different options:

●

Creating a subnet

●

Connecting two target devices via a new subnet

●

Connecting devices to an existing subnet

●

Selecting an existing subnet from the "Subnet" list

You will find the description of the individual methods in the STEP 7 information system.

Networking the serial interface

You will find the supported transmission options of the CP depending on the interface in the

section Overview: Connection to LAN / WAN (Page 59).

Recommendation networking:
To network the interfaces with a WAN network, the following procedure is recommended:
1.

Network the WAN networks in the network view of STEP 7.
In the graphic network view, you have an overview of the subnets of the entire system in

the project.

First configure the interface parameters described in the section WAN settings (Page 70):
–

WAN type

–

Network type

–

Network node type

–

Modem type

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Руководство по эксплуатации, Страница: 82 / 230

Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы: