Siemens SIMATIC S7-1200 CP 1243-8 IRC страница 49 Скачать руководство пользователя

Страница: 49 / 230

Installation, connecting up, commissioning

3.2 Installing, connecting up and commissioning

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

WARNING

If the cable or conduit entry point exceeds 70 °C or the branching point of conductors

exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air

ambient in excess of 50 °C, only use cables with admitted maximum operating temperature

of at least 80 °C.

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage.

This is the case if you only operate devices with SELV (safety extra-low voltage).

3.1.3

Notices about use in hazardous areas according to UL HazLoc

WARNING

EXPLOSION HAZARD
DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE

NON-HAZARDOUS.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-

hazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations

only.

3.2

Installing, connecting up and commissioning

Prior to installation and commissioning

CAUTION

Read the system manual "S7-1200 Programmable Controller"
Prior to installation, connecting up and commissioning, read the relevant sections in the

system manual "S7-1200 Programmable Controller", refer to the documentation in the

Appendix.
When installing and connecting up, keep to the procedures described in the system manual

"S7-1200 Programmable Controller".

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды