Siemens SIMATIC S7-1200 CP 1243-8 IRC страница 54 Скачать руководство пользователя

Страница: 54 / 230

Installation, connecting up, commissioning

3.3 Note on operation

CP 1243-8 IRC

Operating Instructions, 02/2018, C79000-G8976-C385-03

Commissioning the module

The remaining steps in commissioning involve downloading the STEP 7 project data. One

requirement for the full commissioning of the module is the completeness of the STEP 7

project data, see Configuration (Page 55).
The STEP 7 project data of the CP is transferred when you load to the station. To load the

station, connect the engineering station on which the project data is located to the Ethernet

interface of the CPU.
You will find more detailed information on loading in the following sections of the STEP 7

information system:

●

“Loading project data"

●

“Using online and diagnostics functions"

Dismantling

WARNING

Keep to the order when dismantling
Remove the plugs of the data cable from the TS module and from the CP before you

remove the power plug from the CP and therefore disconnect the ground connection of the

devices.

Pull down the two lower DIN rail clamps on the rear of the devices with a slotted

screwdriver.
This releases the locking mechanism.

Swing the devices out of the DIN rail profile to the front.

Note
Time synchronization for telecontrol via SINEMA RC
When using SINEMA Remote Connect for telecontrol communication, set the CPU time

manually during commissioning; see note in section Telecontrol via SINEMA RC (Page 68).

3.3

Note on operation

NOTICE
Closing the front panels
To ensure interference-free operation, keep the front panels of the module closed during

operation.

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды