Siemens SIMATIC S7-1200 CP 1243-8 IRC страница 66 Скачать руководство пользователя | Manualshive

Страница: 66 / 230

background image

Configuration

4.5 Configuration in STEP 7 Basic

CP 1243-8 IRC

66

Operating Instructions, 02/2018, C79000-G8976-C385-03

●

DNP3
The CP acknowledges a request of the master with its reply frames.
The acknowledgment of frames that the CP sends to the master is configured with the

parameters "Connection confirmation" and "Monitoring time for unsolicited frames", see

section Transmission settings – DNP3 (Page 75).

●

IEC
The CP acknowledges a request of the master with its reply frames.
The acknowledgment of frames that the CP sends to the master is configured with the

parameters "Send sequence number" and "Receive sequence number", see section

Transmission settings - IEC (Page 77).

Open User Communication
The successful sending and receipt of frames is indicated by status displays of the program

blocks.
With TCP segments, the protocol-specific acknowledgement mechanisms are used.

4.5

Configuration in STEP 7 Basic

Requirement

The complete configuration of the CP in STEP 7 Basic is only possible after configuring in

STEP 7 V5 (see above).

Overview of configuration in STEP 7 Basic

Follow the steps below when configuring:
1.

Create a STEP 7 project.

2.

Insert the S7-1200 CPU for the SIMATIC station.

3.

Create the PLC tags required for the data points in the CPU, see also point 7.

4.

Select the CP 1243-8 in the catalog and set the firmware version of the CP in the catalog

using the "Version" drop-down list.
–

To use the CP with the functions of a TIM 3V-IE Advanced in a SINAUT ST7 system,

select version V2.1.

–

In all other cases, select a version with V3.0 or higher.

5.

Insert the CP selected in the catalog into the stations.

6.

Importing configuration data from STEP 7 V5:
The function is supported only for the CP with firmware version V2.1. If you are using the

CP with firmware version V3, continue at step 7.
If you are using the CP with the functions of a TIM 3V-IE Advanced for a SINAUT ST7

system, in the parameter group "Partners" import the configuration data of the TIM from

«
...
64
65
66
67
68
...
»

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренд: 3xLogic Страницы: 2

Бренд: Acces I/O products Страницы: 5

SINUS H PROFInet

Бренд: Enertronica Santerno Страницы: 34

Бренд: FDI Страницы: 2

NetVanta Analog Modem Dial Backup Interface Module

Бренд: ADTRAN Страницы: 2

LEDWALL Optimizer HQ P2

Бренд: Gundermann VIDEOWALL Страницы: 12

Бренд: S&P Страницы: 3

Бренд: ProSoft Страницы: 53

Fibe-Air IP-10G

Бренд: Ceragon Страницы: 71

Бренд: Enterasys Страницы: 2

Бренд: StetSom Страницы: 18

Бренд: Airaya Страницы: 28

Бренд: Acromag Страницы: 20

Бренд: StarTech.com Страницы: 9

Бренд: Hitachi Страницы: 17

Бренд: Hitachi Страницы: 53

Бренд: Hitachi Страницы: 23

Бренд: Hitachi Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды