Siemens SIMATIC S7-1200 CP 1243-8 IRC страница 46 Скачать руководство пользователя

Страница: 46 / 230

LEDs and connectors

2.3 Electrical connectors

CP 1243-8 IRC

Operating Instructions, 02/2018, C79000-G8976-C385-03

2.3.2

Ethernet interface X1P1

Ethernet interface

The Ethernet connector is located behind the lower hinged cover of the module. The

interface is an RJ-45 jack according to IEEE 802.3.
The pin assignment and other data relating to the Ethernet interface can be found in the

section Technical data (Page 183).

2.3.3

Serial connection for TS module

Connector for TS module

The connector for a TS module is located on the left-hand side of the CP under the cover.

See also section Installing, connecting up and commissioning (Page 49).

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды