Siemens SIMATIC S7-1200 CP 1243-8 IRC страница 20 Скачать руководство пользователя

Страница: 20 / 230

Application and functions

1.6 Security functions

CP 1243-8 IRC

Operating Instructions, 02/2018, C79000-G8976-C385-03

●

Online functions
From an engineering station (ES) on which STEP 7 is installed, you can use the online

functions of STEP 7 via the Ethernet interface of the CP to access the S7-1200 CPU if

the station is located in the same IP subnet.
The following online functions are available:
–

Downloading project or program data from the STEP 7 project to the station

–

Querying diagnostics data on the station

–

Downloading firmware files to the CP

For a remote station located in a different IP subnet or that can be reached via the

Internet, these functions can only be used if the ES (with CP 1628 or via SCALANCE S)

is connected to the station via a VPN tunnel.

●

SNMP
As an SNMP agent, the CP supports data queries using SNMP (Simple Network

Management Protocol).
For more detailed information, refer to section SNMP (Page 175).

1.6

Security functions

With Industrial Ethernet Security, individual devices, automation cells or network segments

of an Ethernet network can be protected.
Read the information in the section Security recommendations (Page 55) for planning and

configuring your networks.

Security functions of the telecontrol and transmission protocols

For the telecontrol communication, the following Security functions can be activated:

●

ST7
The transmission protocols that can be used by the CP for telecontrol communication via

the ST7 protocol support the following Security functions:
–

MSC
The MSC protocol supports authentication of the communications partners and simple

encryption of data. A user name and a password are included in the encryption. An

MSC tunnel is established between the MSC station and MSC master station.

–

MSCsec
MSCsec supports authentication of the communications partners and data encryption

with a user name and password. In addition to this, the shared automatically

generated key is renewed between the communications partners at configurable

intervals.

●

DNP3
The security functions specific to DNP3 can be used.

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Руководство по эксплуатации

Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Похожие инструкции для SIMATIC S7-1200 CP 1243-8 IRC

Бренды по названию

Популярные бренды