Siemens SIMATIC S7-1200 CP 1243-8 IRC Скачать руководство пользователя страница 59

Страница: 59 / 230

Configuration

4.3 Overview: Connection to LAN / WAN

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

●

STEP 7 Basic
–

Importing the configuration data from STEP 7 V5

–

Configuration of further parameters of the CP, its data points and messages to be sent

–

Downloading the project data from the engineering station to the S7 station

You will find the description of the procedure as of the section Configuration in STEP 7

Basic (Page 66).

4.3

Overview: Connection to LAN / WAN

Supported network types

The CP makes telecontrol communication possible for the various telecontrol protocols via

the network types listed below.
Connection via the Ethernet interface of the CP:

●

IP-based communication via the Ethernet interface
Supported protocols: ST7, DNP3, IEC
–

Industrial Ethernet
Communication in the LAN (copper / fiber-optic cable)

–

Internet
Communication via the Internet

–

IP-based wireless network
Communication via IP-based wireless networks

●

Classic WAN communication via the serial interface
Supported protocols: ST7
With communication via the network types listed below, in addition to the CP a TS

module, modem or router must be used.
–

Dedicated line (incl. analog wireless network)
Communication via dedicated lines or analog wireless networks

–

Analog dial-up network
Communication via the analog dial-up network

–

ISDN network
Communication via the ISDN network

–

Mobile wireless network
IP-based communication via mobile wireless networks (GSM/GPRS, UMTS, LTE)

Содержание SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы:

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Руководство по эксплуатации, Страница: 59 / 230

Результаты поиска

Содержание SIMATIC S7-1200 CP 1243-8 IRC

Отзывы: