Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series Скачать руководство пользователя страница 66

Страница: 66 / 73

Technical specifications

7.1 Technical specifications

Analog input module F-AI 4xI 0(4)..20mA 2-/4-wire HF (6ES7136-6AA00-0CA1)

Manual, 08/2018, A5E41448857-AB

Article number

6ES7136-6AA00-0CA1

Encoder

Connection of signal encoders

•

for current measurement as 2-wire transducer

Yes

–

Burden of 2-wire transmitter, max.

650

Ω

•

for current measurement as 4-wire transducer

Yes

Errors/accuracies

Linearity error (relative to input range), (+/-)

0.1 %

Temperature error (relative to input range), (+/-)

0.023 %/K

Repeat accuracy in steady state at 25 °C (relative to

input range), (+/-)

0.1 %

Operational error limit in overall temperature range

•

Current, relative to input range, (+/-)

2 %

Basic error limit (operational limit at 25 °C)

•

Current, relative to input range, (+/-)

0.1 %

Interference voltage suppression for f = n x (f1 +/- 1 %),

f1 = interference frequency

•

Series mode interference (peak value of interfer-

ence < rated value of input range), min.

40 dB

•

Common mode interference, min.

70 dB

Interrupts/diagnostics/status information

Diagnostics function

Yes, "Alarms/diagnostic messages" section

in the manual

Alarms

•

Diagnostic alarm

Yes

•

Limit value alarm

Yes

Diagnostic messages

•

Monitoring the supply voltage

Yes

•

Wire-break

Yes; Measuring range 4 to 20 mA only

•

Short-circuit

Yes

Diagnostics indication LED

•

RUN LED

Yes; Green LED

•

ERROR LED

Yes; Red LED

•

Monitoring of the supply voltage (PWR-LED)

Yes; green PWR LED

•

Channel status display

Yes; Green LED

•

for channel diagnostics

Yes; Red LED

•

for module diagnostics

Yes; Green/red LED

Содержание SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series










































































Результаты поиска

Содержание SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series, Руководство пользователя

Результаты поиска

Содержание SIMATIC ET 200SP F-AI 4xI 0(4) 20mA 2-/4-wire HF Series

Отзывы:

Бренды по названию

Популярные бренды