Siemens SICAM 7KG85X Скачать руководство пользователя страница 65

Страница: 65 / 281

[sc_q100_communication ethernet, 3, en_US]

Figure 2-26

Configuration Tab, Ethernet Settings

•

Configure the respective parameters according to the following table.

Table 2-18

Settings for Communication Ethernet

Parameter

Default Setting

Setting Range

Communication Ethernet
IP address

192.168.0.55

Any
0.0.0.0 = DHCP

Subnet mask

255.255.255.0

Any

Default gateway

192.168.0.1

Any

Ethernet switch on

No
Yes

Enable SNMP

No
Yes

Bus protocol

Modbus TCP

-None-
Modbus TCP
IEC 61850

•

After the parameterization, click Send.

•

In the navigation window, click Activation and cancel.

•

Enter the activation password (refer to

Table 2-3

•

Click Activation.

Configuration via Display

Submenu Ethernet Settings

The operation is carried out with the softkeys F1 to F4.

2.6.1.3

After the parameter changes have been enabled, the device will restart.

Basic Functions
2.6 Ethernet Communication

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Содержание SICAM 7KG85X


























































































































































































































































































Результаты поиска

Содержание SICAM 7KG85X

Отзывы:

Siemens SICAM 7KG85X, Руководство пользователя, Страница: 65 / 281

Результаты поиска

Содержание SICAM 7KG85X

Отзывы: