manualshive.com logo in svg

Siemens SICAM 7KG85X, Руководство пользователя, Страница: 235 / 281

Поделиться
Скачать
Siemens SICAM 7KG85X Скачать руководство пользователя страница 235

Failures and LED Displays

General Inspection

Visual Inspection

If function failures occur, first check the device visually. Observe the following points when inspecting the
device visually:

•

Correct installation of the device at the intended location as described in chapter 

9.3 Assembly

•

Compliance with the environmental conditions specified in chapter 

12.1.4 Environmental Conditions and

Climatic Stress Tests

•

Correct connection of supply voltage and grounding conductors according to chapter 

9.5 Electrical

Connection

•

Correct connection of measuring and communication lines according to chapter 

9.5 Electrical Connection

Function Checks

Additionally, check the following aspects:

•

Functioning of the display according to chapter 

9.10 Operation via Display

 and good visibility of the

display

•

Correct functioning of peripheral devices (for example connected PC, series-connected current trans-
formers)

•

Compliance with the access rights according to chapter 

9.1 Safety Notes and Access Rights

•

Compliance with the commissioning sequence of the device according to chapter 

9.12 Commissioning

•

Evaluation of the LED failure indications, see chapter 

10.1 Failures and LED Displays

Troubleshooting and Repair

General Troubleshooting

You are not authorized to do troubleshooting for the defective device beyond the measures described in
chapter 

10.1.1 General Inspection

 and make repairs on your own. Special electronic modules are inserted in

SICAM P850/P855 which can only be replaced by the manufacturer according to the guidelines for Electro-
static sensitive devices (ESD).
If you suspect any damage on the device, Siemens recommends sending the entire device to the manufac-
turer. For this purpose, it is best to use the original transport packaging or similar packaging.

Troubleshooting Based on Error Messages

i

i

NOTE

Error messages are service information that you provide upon request to the service department in case of
an error.

For more information, refer to 

Viewing and Clearing of Error Logs, Page 82

.

10.1

10.1.1

10.1.2

Troubleshooting, Repair, and Fallback Mode
10.1 Failures and LED Displays

234

SICAM, SICAM P850/P855 7KG85X, Manual

E50417-H1040-C482-A9, Edition 03.2022

Содержание SICAM 7KG85X


























































































































































































































































































Отзывы:

Нет отзывов