manualshive.com logo in svg

Siemens RUGGEDCOM RX1510, Руководство по установке

Поделиться
Скачать
Siemens RUGGEDCOM RX1510 Скачать руководство пользователя страница 19

Installing the Device
2.5.1 Connecting High AC/DC Power

• The maximum wire length between the terminal block and power source must

not exceed 6 m (20 ft) for 24 V power supplies or 18 m (60 ft) for 48 V power

supplies.

• For 125/230 VAC rated equipment, an appropriately rated AC circuit breaker

must be installed.

• For 125/250 VDC rated equipment, an appropriately rated DC circuit breaker

must be installed.

• It is recommended to provide a 20 A circuit breaker for the power module.
• Equipment must be installed according to applicable local wiring codes and

standards.

2.5.1

Connecting High AC/DC Power

To connect a high AC/DC power supply to the device, do the following:

DANGER

Electrocution hazard – risk of death, serious personal injury and/or damage to

the device

Make sure the supplied cover is always installed over high voltage screw terminal

blocks.

CAUTION

Electrical hazard – risk of damage to equipment

Do not connect AC power cables to a 12, 24 or 48 VDC power supply terminal block.

Damage to the power supply may occur.

Note

The screw terminal block is installed using Phillips screws and compression plates, al-

lowing either bare wire connections or crimped terminal lugs. Use #6 size ring lugs

for secure, reliable connections.

10

RUGGEDCOM RX1510

Installation Manual, 12/2019, C79000-G8976-1055-16

Содержание RUGGEDCOM RX1510































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды