Siemens RUGGEDCOM RX1510 Скачать руководство пользователя страница 12

Страница: 12 / 62

Introduction

1.3 Required Tools and Materials

• Red = Alarm

Compact Flash Card Port

Houses the CompactFlash (CF) card that contains active and back-

up installations of RUGGEDCOM RUGGEDCOM RX1510, along with

the configuration database and other system data. For more infor-

mation, refer to

"Accessing the CompactFlash Card (Page 20)"

1.3

Required Tools and Materials

The following tools and materials are required to install the RUGGEDCOM RX1510:

Tools/Materials

Purpose

AC/DC power cord (16 AWG)

For connecting power to the device.

Lightning protector

For protecting the device from harmful electrical

strikes.

Shielded coaxial cables

For connecting the device to antennas and an Eth-

ernet network.

SIM Card(s) provided by the network carrier

For accessing a network carrier's cellular net-

work. Required only if a cellular modem module is

equipped.

Flathead screwdriver

For mounting the device to a DIN rail.

Phillips screwdriver

For mounting the device to a panel.

4 x #6-32 screws

For mounting the device to a panel.

Braided or equivalent ground wire

For grounding the device to safety Earth.

1.4

Decommissioning and Disposal

Proper decommissioning and disposal of this device is important to prevent malicious

users from obtaining proprietary information and to protect the environment.

Decommissioning

This device may include sensitive, proprietary data. Before taking the device out of

service, either permanently or for maintenance by a third-party, make sure it has

been fully decommissioned.
For more information, refer to the associated

User Guide

Recycling and Disposal

For environmentally friendly recycling and disposal of this device and related acces-

sories, contact a facility certified to dispose of waste electrical and electronic equip-

ment. Recycling and disposal must be done in accordance with local regulations.

RUGGEDCOM RX1510

Installation Manual, 12/2019, C79000-G8976-1055-16

Содержание RUGGEDCOM RX1510































































Результаты поиска

Содержание RUGGEDCOM RX1510

Отзывы:

Бренды по названию

Популярные бренды

Siemens RUGGEDCOM RX1510, Руководство по установке

Результаты поиска

Содержание RUGGEDCOM RX1510

Отзывы:

Бренды по названию

Популярные бренды