Siemens POLYMOBIL Plus Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 50

Siemens POLYMOBIL Plus Скачать руководство пользователя страница 8

POLYMOBIL Plus

SPR8-125.061.02

Page 4 of 4

Siemens AG

Rev. 01

01.00

TD SD 24

Medical Engineering

1 - 4

Prerequisites

•

Connect the POLYMOBIL Plus only to a line voltage supply (line voltage receptacle) that
complies with the requirements of VDE 0107, or corresponds to the local national
regulations.

•

Disconnect the POLYMOBIL Plus at the line voltage

OFF

switch on the operating

console and disconnect the

line voltage plug

prior to any service work

.

•

Remove or insert boards with the generator switched OFF only; observe
ESD guidelines when handling boards.

Replacing damaged or missing screws

1

•

Damaged or missing screws may only be replaced by steel screws as specified in the
installation drawings conforming to DIN267 and must have the specified tensile strength.

Cleaning

1

•

The unit must always be switched off or disconnected before cleaning.

•

Use only water to clean the unit or a lukewarm, dilute solution consisting of water and a
household cleaning agent.

•

Do not use abrasive cleaning agents or organic solvents such as benzine, alcohol or spot
remover. Do not spray with water.

•

For additional information, refer to the Operating Instructions "Cleaning/Disinfection".

All Allen screws must have a tensile strength rating of 8.8.

CAUTION

«
...
6
7
8
9
10
...
»

Содержание POLYMOBIL Plus



















































Отзывы:

Нет отзывов