Siemens POLYMOBIL Plus Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 50

Siemens POLYMOBIL Plus Скачать руководство пользователя страница 30

POLYMOBIL Plus

SPR8-125.061.02

Page 8 of 20

Siemens AG

Rev. 01

01.00

TD SD 24

Medical Engineering

5 - 8

Measurements

Measuring the oscillating current

5

•

Switch

OFF

POLYMOBIL Plus and wait until the capacitor voltage has dropped to a

value < 10 V.

•

Disconnect the cable from the inverter to capacitor C1 and push the cable through the
current transformer 50 A : 50 mA (with a parallel resistor of 10 ohms) and connect the
cable again.

•

Connect the oscilloscope to the current transformer.

•

Switch

ON

POLYMOBIL Plus .

•

Set 60 KV, 10 mAs on POLYMOBIL Plus and release exposure.

The diagram must correspond to Fig 8.

Prior to beginning the following instructions, you must discharge
the capacitor bank, because life-threatening DC voltage is
present. Check the actual charge with the DVM.

The maximum main inverter frequency can only be measured in
the ascending part of the high voltage, i.e. in the first microsec-
onds, because afterwards the frequency is lower.

WARNING

CAUTION

Fig. 8

CH2: 1 V/Div, Trigger: Test point "TRG" external on D 915
20 µs /Div

«
...
28
29
30
31
32
...
»

Содержание POLYMOBIL Plus



















































Отзывы:

Нет отзывов