Siemens POLYMOBIL Plus Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 50

Siemens POLYMOBIL Plus Скачать руководство пользователя страница 19

Troubleshooting

3 - 3

Siemens AG

SPR8-125.061.02

Page 3 of 4

POLYMOBIL Plus

Medical Engineering

Rev. 01

01.00

TD SD 24

Err 8

Braking failure (error when braking the rotating anode - a current was
measured in the auxiliary capacitor C2 during the braking.)

- D915TP ’I1’. No current must be measured here when braking.
- D915 TP ’I2’. Braking current must be measured here.
- TRIAC ’V7’ or ’V8’ defective? => Replace D925.

Err 9

Pressure switch (oil pressure switch in the single tank generator is
active)

- Tube is overheated?
- Measure D915 plug X8 at pin 8. In case of malfunction, 0V are measured.

Err 10

Rot = 0 (rotating anode speed is 0 on exposure)

The error is only displayed as long preparation is depressed.

- LED ’AR’ on D925 flashes ; is fuse F5 ok?
- Measure at TP ’I1’ and ’I2’. Current has to be present during acceleration.
- Check D925.
- Is the power factor correction capacitor C2 defective?
- Connection to/in the single tank generator ok?

Err 11

Short circuit in main inverter

- Check D960 .
- Check D915 .
- Main inverter frequency too high?

Err 12

KVmax

- Interruption of KVact measurement. Measure TP ’KVN’ and ’KVP’ on D915.

Both signals must have the same amplitude.

- ’KVN’ or ’KVP’ > 70 kV.
- Error in kV measurement circuit?
- Error in kV control circuit?

Err 13

Imax

The tube or filament current is recorded.

- Check the filament circuit.
- Exposure filament basic value incorrectly set (P5 on D915)?
- Tube arcing?

If kVact < kVnom, Err 14 or Err 13 is detected and displayed. Refer also to the
troubleshooting information under Err 14.

Err 14

KVact < KVnom

- Voltage in the capacitor bank too low (D950 TP ’VC’)?
- Defective capacitors /fuses on the capacitor bank (D970)?
- No KVact?
- Error in the measurement circuit on D915?
- Main inverter frequency too low?
- Defect in the main inverter D960?

Err 15

mA

ACT

<

mA

NOM

- Check the filament circuit.

«
...
17
18
19
20
21
...
»

Содержание POLYMOBIL Plus



















































Отзывы:

Нет отзывов