2-7
Installation
Figure 29
PIM-2 to MXL-IQ Wiring Diagram
PIM-2 (REAR VIEW)
OUTPUT
SW1
(REFER TO TABLE 4)
PWR
INPUT
PARALLEL PRINTER (REAR VIEW)
CENTRONICS PARALLEL
ANN-1
MKB-4
PIM-1
SEE INSTL. INSTR.
P/N 315-091462
TB1
CABLE SUPPLIED WITH PIM-2
(SEE NOTE 2)
SUPERVISED
(REFER TO NOTES 9 AND 10)
THE CONNECTION IS NOT
SUPERVISED FOR DATA
INTEGRITY BETWEEN PIM-2
AND THE PRINTER.
CABLE NOT SUPPLIED
(SEE NOTE 1)
SUPERVISED
PIM-2 POWER CABLE
MUST BE IN CONDUIT
INSTALL IN UL LISTED GANGBOX
PIM-2 POWER TRANSFORMER
SUPPLIED WITH PIM-2 (SEE NOTE 3)
120 VAC
60 Hz
XFMR
NOTES:
1.
Maximum cable
distance from PIM-1 to
PIM-2 cable is 25 feet.
The two modules must
be in the same room.
2.
The maximum distance
from the PIM-2 to the
parallel printer is 6 feet.
The two modules must
be in the same room.
3.
PIM-2 power (PWR) is
connected to the 5
VDC, 600mA trans-
former supplied with the
PIM-2. The transformer
requires 120 VAC, 60
Hz, 0.5A max.
4.
For NFPA 72 Local,
Auxiliary, and Remote
Station configurations,
connect the output of
the PIM-2 to any UL
listed EDP Centronics
parallel printer.
5.
The parallel printer must
support the EPSON FX
command set.
6.
The PIM-2 input and
output connectors are
DB-25 female.
7.
Pressing RESET on the
PIM-2 causes the unit
to read the SW1
settings. The status
LED is lit when the unit
is powered. Do not use
the COPY button.
8.
For NFPA Proprietary
and UL 1076
configurations, use
parallel printer Model
PAL-1, a UL listed for
fire Centronics parallel
printer.
9.
The parallel printer is
supervised for AC, on/
off line, paper out, paper
jam, and connection to
the PIM-2.
10. The PIM-2 is
supervised for power,
connection to the
printer, and connection
to the PIM-1.
11. After loading paper in
the PAL-1 printer, turn
off the power and follow
the steps below:
•
While pressing the
LOAD PARK button,
turn on the power to
the PAL-1 printer.
Continue pressing
the LOAD PARK
button for 5 seconds.
•
Release the LOAD
PARK button.
•
The current setting
will print.
•
When printing is
completed, the ON
LINE indicator will be
lit. If the ON LINE
indicator is not lit,
press the ON LINE
button.
4
E
L
B
A
T
S
R
E
T
E
M
A
R
A
P
N
O
I
T
A
C
I
N
U
M
M
O
C
E
C
A
F
R
E
T
N
I
L
A
I
R
E
S
2
-
M
I
P
f
o
r
a
e
r
t
a
d
e
t
a
c
o
L
-
)
1
W
S
(
n
oi
ti
s
o
P
h
c
ti
w
s
p
i
D
1
2
3
4
5
6
7
8
E
T
A
R
D
U
A
B
0
0
6
9
0
0
8
4
0
0
4
2
0
0
2
1
0
0
3
F
F
O
N
O
F
F
O
N
O
N
O
N
O
N
O
F
F
O
F
F
O
N
O
F
F
O
F
F
O
N
O
N
O
N
O
S
TI
B
A
T
A
D
8
7
F
F
O
N
O
Y
TI
R
A
P
n
e
v
E
d
d
O
F
F
O
N
O
Y
TI
R
A
P
el
b
a
si
D
el
b
a
n
E
F
F
O
N
O
L
O
R
T
N
O
C
W
O
L
F
e
r
a
w
d
r
a
H
e
r
a
w
tf
o
S
F
F
O
N
O
E
P
Y
T
T
R
O
P
F
F
O
NOTE:
When setting Switch S1,
OFF=UP=OPEN
ON=DOWN=CLOSED
Содержание MXL-IQ
