Siemens HR676G8.1A, Инструкция по эксплуатации

Страница: 27 / 64

Cleaning function
en
27
Note:
When using the cleaning function, you can clean
the enamel accessory provided at the same time. You
cannot clean any of the wire racks when using the
cleaning function. The wire racks are not suitable for
cleaning using the cleaning function; this will discolour
them. Further accessories suitable for cleaning using
the cleaning function are listed in the table for special
accessories.
~
"Accessories" on page 13
:
Warning
Risk of fire!
■
Loose food residues, grease and meat juices may
catch fire during the cleaning function. Before
starting the cleaning function, remove coarse dirt
from the cooking compartment and from the
accessories.
Risk of fire!
■
The appliance will become very hot on the outside
during the cleaning function. Never hang
combustible objects, e.g. tea towels, on the door
handle. Do not place anything against the front of
the appliance. Keep children away from the
appliance.
:
Warning
Risk of serious damage to health!
The appliance will become very hot during the cleaning
function. The non-stick coating on baking trays and tins
is destroyed and noxious gases are released. Never
clean non-stick baking trays and baking tins using the
cleaning function. Only clean enamelled accessories
using the cleaning function.
Setting the self-cleaning function
1.
Press the menu button.
The operating modes menu opens.
2.
Select the "Self-cleaning" operating mode.
Cleaning setting 3 is suggested. You can start the
cleaning process immediately using the "Start/stop"
button or
3.
select a different cleaning setting using the rotary
selector.
4.
Press the "Start/stop" button to start the cleaning
operation.
The cooking compartment door locks shortly after
operation starts. The
H
symbol for the locking
mechanism appears on the right-hand side of the status
bar next to the elapsing duration.
The cooking compartment door cannot be opened until
the
H
symbol goes out in the status bar.
Once the cleaning has finished
An audible signal sounds. The oven stops heating.
“Finished” appears in the status bar. Use the
0
button
to switch off the audible signal. “Appliance cooling
down” appears in the status bar.
Cancelling the cleaning operation
Use the "On/off" button to switch off the oven. The
cooking compartment door cannot be opened until the
H
symbol goes out in the status bar.
Adjusting the cleaning setting
Once cleaning starts, the cleaning setting can no longer
be changed.
You can set the cleaning to run overnight
In the section "Time settings", you can find out how to
delay the end time. This allows you to use the oven at
any time throughout the day.
~
"Time-setting options"
on page 21
Once the cleaning function has ended
Once the cooking compartment has cooled down, wipe
off the ash that has been left behind in the cooking
compartment and around the appliance door with a
damp cloth.
Descaling
The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling programme.
For hygiene reasons, the descaling programme must
be run through completely so that the appliance can be
ready for operation again.In total, the descaling
programme runs for approx. 70-90 minutes.
■
Descale (approx. 55-70 minutes), then empty and
refill the water tank
■
First rinsing cycle (approx. 6-9 minutes), then empty
and refill the water tank
■
Second rinsing cycle (approx. 6-9 minutes), then
empty and dry the water tank
If the descaling process is interrupted (for example, due
to a power failure or because the appliance has been
switched off), you are prompted to rinse the appliance
twice after it is switched back on. The appliance cannot
be used until the second rinsing cycle has come to an
end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
Damage to the appliance: Only use liquid descalers
recommended by us for the descaling programme.
Other descalers may damage the appliance.
Descaler order no.: 311 680
Caution!
Descaling solution: Do not allow the descaling solution
to come into contact with the control panel or other
sensitive surfaces. This will damage the surfaces. If this
does happen, remove the descaling solution
immediately with water.