Siemens EH675TK11E Скачать руководство пользователя страница 98

Страница: 98 / 113

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 98 von 113

5.19 Check polybox connections

The procedure is as follows:

1) Check that the cable and connector that goes from the Polybox

box to the oven is connected and in the correct position.

2) Check that the cable and connector that goes from the Polybox

box to the hob is connected

If all of this is good connected, open polybox box

3) Check that both connectors (oven-polybox and hob-polybox)

are good connected in the wake up module.

5.19.1 Oven connector

It should be verified that the connector that comes out of the box and
goes in the oven is not polarized.

The polarized connector is connected in the wake up module.

5.19.2 Hob connector

Check that the cable and connector that goes from the Polybox box to
the hob is connected. See electrical diagram

Содержание EH675TK11E


















































































































Результаты поиска

Содержание EH675TK11E

Отзывы:

Siemens EH675TK11E, Инструкция по ремонту, Страница: 98 / 113

Результаты поиска

Содержание EH675TK11E

Отзывы: