Siemens EH675TK11E Скачать руководство пользователя страница 93

Страница: 93 / 113

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 93 von 113

5.16 Check of residual heat indication

We have two levels which indicate residual heat:

“h” for lower temperatures or operating times

“H” for higher temperatures or longer operating times.

Warning!

Avoid touching the cooking zone showing this indication.

5.16.1 Induction zones

The h/H remain lit while they are above certain temperature values.

The temperature is measured by the NTC of the inductor and it is the
ELIN which transfers the value to the touch Control.

The residual heat indication doesn’t appear while the zone is giving
power. It only appears when the zone is not working or when there is
no pan above.

The indication is programmed to appear in the cooling curve after a
heating upper 100 ºC.

It can be measured above the glass ceran with a temperature

sensor for surfaces with the following spare part number.

Spare part number 341176

Spare part number 340961

Содержание EH675TK11E


















































































































Результаты поиска

Содержание EH675TK11E

Отзывы:

Siemens EH675TK11E, Инструкция по ремонту, Страница: 93 / 113

Результаты поиска

Содержание EH675TK11E

Отзывы: