Siemens EH675TK11E Скачать руководство пользователя страница 43

Страница: 43 / 113

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 43 von 113

3.12 Relay module for FlexInduction

►

The relay module is unique for all the models. It can be
mounted in both sides of the ELIN. On the left for
combisurface on the left ,and on the right for combisurface on
the right.

That means, that the relay module for combisurface on the right and
on the left is the same, but depending on the zone we must turned it

Besides, it comes printed with the connection´s colour in englisch, in
order to make easier the right connection

3.12.1 Relay module function

This module forwards the current towards an inductor or another
different, according to the previous pan detection in the ELIN..

We have normally 2 branches per ELIN for two inductors.

Thanks to this additional relay module, we can feed 4 inductors
instead of 2 inductors

Содержание EH675TK11E


















































































































Результаты поиска

Содержание EH675TK11E

Отзывы:

Siemens EH675TK11E, Инструкция по ремонту, Страница: 43 / 113

Результаты поиска

Содержание EH675TK11E

Отзывы: