manualshive.com logo in svg

Siemens EH675TK11E, Инструкция по ремонту, Страница: 57 / 113

Поделиться
Скачать
Siemens EH675TK11E Скачать руководство пользователя страница 57

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 57 von 113 

5.6 

Checking the level of supplied power Problem 

 

Low level of supplied power 

 

Less power is supplied with the new inductor 

 

5.6.1 

Cause 

  The pot is not suitable. See list of suitable pots and check the 

pot detection system. 

  The new IH5-I technology supplies less power than the old IH4-

I technology (ind IV). See regulations. 

  Certain regulations governing power have come into force. See 

regulations. 

  The positioning spring that brings the inductors closer to the 

glass is not in place. 

See position of the spring. 

5.6.2 

Solution 

5.6.2.1 

Power regulation 

 

5.6.2.1.1  Booster power regulation 

For the first ten minutes, the Booster operates at maximum 
power, in other words, it supplies 150% of inductor power. 
Subsequently, the booster is regulated and lowered to power 
level 9. 
If the user wishes to reactivate the booster, this can be done. 
The booster will supply maximum power for a further 2 
minutes and then return to power level 9. After the 12 
minutes with the booster at maximum power, if the user tries 

to reactive it once more, only 83% of the 150% of inductor 
power will be supplied and then it will return to power level 9 
(100% inductor power). 
At this time, if the user wishes to activate the booster again, 
they must wait for the same period of time as the time they 
wish it to be activated for, provided that this is less than 10 
minutes. 
 

Superbooster (Paella dish) 

On these models, it is not possible to reactivate the booster 
after the initial 10 minutes at maximum power. 
If it has been used for 10 minutes, we must wait for 10 
minutes in order to try and activate it again. 
If we have used it for 5 minutes, we must wait for 5 minutes 
in order to try and activate it again. 
 
 

5.6.2.2 

Содержание EH675TK11E


















































































































Отзывы:

Нет отзывов