Siemens EH675TK11E Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 113

Siemens EH675TK11E Скачать руководство пользователя страница 100

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 100 von 113

5.20 Claim: frying function doesn´t work

Warning!

The frying/cooking ´s NTCs don´t show the mistake d4 or d5 when
they are not connected or damaged

5.20.1 In induction hobs with LCD

If the frying /cooking ´s NTC is damaged or even not connected, it is
possible that the customer can go into the menu for frying function,
selects the desired niveau and, once the function is activated, it is
showed in display the desired niveau, but the animation that the zone
is heating (in red) , is not showed.

In these cases, it must be checked or connected the frying/cooking ´s
NTC.

The 15 cm inductors with frying sensor function activate the frying
sensor function with a bridge. See frying sensor function

5.20.2 In induction hobs without LCD

If the frying/cooking ´s NTC is damaged or even is not connected,
when you choose the sensor to activate the frying/cooking function, it
sounds the acustic signal “mal operation” (long signal)

That is, it is not possible to use the frying sensor function.

The 15 cm inductors with frying sensor function activate the frying
sensor function with a bridge. See frying sensor function

«
...
98
99
100
101
102
...
»

Содержание EH675TK11E


















































































































Отзывы:

Нет отзывов