Siemens EH675TK11E Скачать руководство пользователя страница 82

Страница: 82 / 113

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 82 von 113

5.11 Cookware for induction and recommendations

5.11.1 General

All saucepans and frying pans with a ferromagnetic base are
suitable for induction.

Only pots whose base is uniformly in contact with the magnet
should be used (check the entire base).

When using other types of pots, the inductor does not heat up
and the power level display will flash.

The minimum diameter of the pot should also be taken into
consideration.

5.11.2 Suitable saucepans and frying pans

Enamelled steel saucepans and frying pans

Cast iron saucepans and frying pans

Iron saucepans

Stainless steel saucepans and frying pans, provided that they
have a special ferromagnetic base for induction purposes

5.11.3 Unsuitable saucepans and frying pans

Non-ferromagnetic or non-metallic materials

Aluminium saucepans and frying pans

Copper saucepans and frying pans

Tin saucepans and frying pans

Standard stainless saucepans and frying pans

Glass containers (“Pyrex”)

Clay pots

5.11.4 Recommendations

5.11.4.1

ITTALA / DEMEYERE

5.11.4.2

Pots and pans

444218

pot 16 cm.

444217

pot 18 cm

444210

pot 20 cm

444216

pot 24 cm

444219

pot 22 cm.

464355

frying sensor pan

Содержание EH675TK11E


















































































































Результаты поиска

Содержание EH675TK11E

Отзывы:

Siemens EH675TK11E, Инструкция по ремонту, Страница: 82 / 113

Результаты поиска

Содержание EH675TK11E

Отзывы: