Siemens EH675TK11E Скачать руководство пользователя страница 106

Страница: 106 / 113

206_58300000141095_ara_en_k.doc – 04.10.a

Seite 106 von 113

5.24 Pot detection for FlexInduction models

Warning!

If the pan is not detected correctly, it is necessary to verify the pan
situation respect to the NTC of the oval inductor.

The aesthethic help us to know where we must place the pots.

5.24.1 Pot detection

The recommendation to obtain a good pot regulation is as follows:

For pot diameters minors of 130 mm ,we must place

them centered in the middle of the oval inductor. The
aesthethic help us to know where we must place the
pots.

For pot diameters major of 130 mm, we must place them

between two oval zones, with both NTC covered.

If we don´t follow these recommendations, the pot can not be
detected in some ocasions



when it is off-centered, it would not be detected for security

5.24.2 Flexible zones aesthetics

5.24.2.1

For Bosch models

Содержание EH675TK11E


















































































































Результаты поиска

Содержание EH675TK11E

Отзывы:

Siemens EH675TK11E, Инструкция по ремонту, Страница: 106 / 113

Результаты поиска

Содержание EH675TK11E

Отзывы: