manualshive.com logo in svg

Siemens EH675TK11E, Инструкция по ремонту, Страница: 52 / 113

Поделиться
Скачать
Siemens EH675TK11E Скачать руководство пользователя страница 52

 
 

206_58300000141095_ara_en_k.doc – 04.10.a 

Seite 52 von 113 

5 

CHECK AND INSTALLATION 

5.1 

NTC sensor checks 

5.1.1 

Inductor NTC 

Each one of the inductors uses an NTC sensor to control operational 
temperature. The inductor NTC is a replaceable part. 

 

5.1.2 

Induction module NTC 

The temperature of the semiconductor devices is measured by two 
NTC sensors that protect the electronics from excessively high 
temperatures. These sensors are not replaceable parts. 

 

5.1.3 

NTC sensor conversion table 

Temp (ºC) 

R (KOhm) 

Temp (ºC) 

R (KOhm) 

10 98.264 26 47.788 
11 93.229 27 45.794 
12 88.632 28 43.873 
13 84.404 29 42.019 
14 80.489 30 40.228 
15 76.845 31 38.496 
16 73.435 32 36.819 
17 70.233 33 35.193 
18 67.213 34 33.616 
19 64.357 35 32.085 
20 61.647 36 30.597 
21 59.070 37 29.150 
22 56.613 38 27.741 
23 54.264 39 26.369 
24 52.016 40 26.065 

25 

49.860 

  

  

 

5.1.4 

Correct position 

It is very easy that they could get out of its housing on removing the 
glas, on raising the inductor set, on changing an ELIN... etc helped by 
the conductive silicone (white paste). 

An incorrectly positioned NTC can cause diverse problems: 

1- 

Power loss

.

 

On having placed the glas the NTC can push 

down the inductor and the distance between the inductor and 
cookware increases, giving as a result a power loss. 

2- 

Wrong inductor regulation

.

 

If the NTC is not in direct contact 

with the glas, the real temperatures are not read. 

Содержание EH675TK11E


















































































































Отзывы:

Нет отзывов