Siemens 7ME6810 Скачать руководство пользователя страница 157

Страница: 157 / 170

Param‐

eter ID

Meter
version

Display
view

Parameter/data type

Factory settings

Data range

Fixed parameter or meter data that are not changeable

811

Advanced -

Leakage source

Flow rate

Flow rate / volume

812

Advanced -

Start period for leakage

detection

120 min = 2:00 [24:00]

0 to 1440 detection minutes (0 to

23:50)

813

Advanced -

Duration leakage detec‐

tion

0 to 144 (10 to 1440 minutes)

814

Advanced -

Leakage value unit

Flow / volume unit

The unit is updated once param‐

eter 811 change is downloaded

to the device and afterwards up‐

loaded to the pc

815

Advanced -

Leakage limit

0 to 1x10

The unit is updated once param‐

eter 811 change is downloaded

to device and afterwards uploa‐

ded to pc

816

Advanced -

- Leakage excitation fre‐

quency

1.5625 Hz

1/60 Hz, 1/30 Hz, 1/15 Hz,

1/5 Hz, 1.5625 Hz, 3.125 Hz,

6.25 Hz

817

Advanced -

Leakage status

No faults

Leakage status:

1: Finished successfully

2: Leakage detection running

3: Leakage detection failed (Sys‐

temStatus have fatal error)

4: Leakage detection failed

(Empty-pipe detection disabled)

5: Leakage detection failed (Coil

current off)

6: Leakage detection failed (In‐

sulation test was active during

detection)

7: Leakage detection stopped

because leakage parameter

was changed.

If none of the above-mentioned

leakage status messages is

pending, the message is "No

faults"

818

Advanced -

Periods with possible

leakage

819

Advanced -

Leakage periods before

alarm

0 to 255

820

Advanced -

Reset leakage period in‐

formation

Yes / No

Value is reset to "No" when up‐

loading device parameters to pc

after command execution

821

Advanced St1

Latest leakage period

flowrate

822

Advanced St1

Latest leakage period vol‐

ume

Parameter lists

F.8 800-899

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

157

Содержание 7ME6810











































































































































































Результаты поиска

Содержание 7ME6810

Отзывы:

Siemens 7ME6810, Руководство по эксплуатации, Страница: 157 / 170

Результаты поиска

Содержание 7ME6810

Отзывы: