Siemens 7ME6810 Скачать руководство пользователя страница 100

Страница: 100 / 170

Output B as call-up output

①

Call up output

②

Call up reset

③

Call up status

④

On - Off

When output B is configured as "call-up", the output is activated by an alarm condition and

remains on until it is reset via meter display key or communication interface.
A new alarm will not activate a "call-up" function if the "call-up" function is still active from a

previous alarm.

Note
Like alarm output, call-up output inverts to a pulse output providing a call-up if power

disappears or cable connection is interrupted.

MAG 8000
When output B is configured as an "call-up" output, it will follow the internal alarms that were

previously chosen in the Alarm Configuration List.

Note
Call-up output is inverted to a pulse output providing an alarm if power disappears or cable

connection is interrupted.

Regional factory default settings

DN
mm

size
(inch)

Pulse width
ms

Amount per

pulse
m

(Europe)

Amount per

pulse
Gallons (USA)

Amount per

pulse
ML (Australia)

25, 40, 50

(1", 1½", 2")

0.01

0.001

65, 80, 100, 125, 150

(2½", 3", 4", 5", 6")

0.1

0.001

200, 250, 300, 350,
400, 450, 500

(8", 10", 12", 14",
16", 18", 20")

100

0.01

600, 700, 800, 900,
1000, 1050, 1100, 1200

(24", 28", 30", 32", 36",
40", 42", 44", 48")

100

0.01

Technical data
10.6 Output characteristics

SITRANS FM MAG 8000

100

Operating Instructions, 03/2020, A5E03071515-AH

Содержание 7ME6810











































































































































































Результаты поиска

Содержание 7ME6810

Отзывы:

Siemens 7ME6810, Руководство по эксплуатации, Страница: 100 / 170

Результаты поиска

Содержание 7ME6810

Отзывы: