manualshive.com logo in svg

Siemens 7ME6810, Руководство по эксплуатации, Страница: 113 / 170

Поделиться
Скачать
Siemens 7ME6810 Скачать руководство пользователя страница 113

MAG 8000 (7ME8610) and MAG 8000 (7ME6820)

Dimensions Inches

Bolting

Size

D

PCD

T

B

Holes

Bolts

ANSI Class 150
1"

4.25

3.12

0.56

0.62

4

9/16"

1 ½"

5

3.88

0.68

0.62

4

9/16"

2"

6

4.75

0.75

0.75

4

5/8"

2 ½"

7

5.5

0.88

0.75

4

5/8"

3"

7.5

6

0.94

0.75

4

5/8"

4"

9

7.5

0.94

0.75

8

5/8"

5"

10

8.5

0.94

0.88

8

3/4"

6"

11

9.5

1

0.88

8

3/4"

8"

13.5

11.75

1.12

0.88

8

3/4"

10"

16

14.25

1.19

1.00

12

7/8"

12"

19

17

1.25

1.00

12

7/8"

14"

21

18.75

1.38

1.12

12

1"

16"

23.5

21.25

1.44

1.12

16

1"

18"

25

22.75

1.56

1.25

16

1 1/8"

20"

27.5

25

1.69

1.25

20

1 1/8"

24"

32

29.5

1.88

1.38

20

1 1/4"

External battery pack and cable

/

Note
Physical orientation of battery pack may influence battery capacity.
Optimal battery capacity is achieved with battery pack in an upright position as shown.

The cable for the battery pack connection must be ordered separately.
For information about battery disposal, see Battery disposal (Page 85).

Technical data

10.12 Dimension drawings

SITRANS FM MAG 8000

Operating Instructions, 03/2020, A5E03071515-AH

113

Содержание 7ME6810











































































































































































Отзывы:

Нет отзывов