Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 75

Страница: 75 / 264

Engineering and remote access

3.4 SIMATIC STEP 7 in the TIA Portal

SITOP UPS1600 / BAT1600 / UPS1100
Equipment Manual, 07.2021, A5E37775406-11-76

Parameters when using third-party batteries

Parameter

Value range

Default setting

Battery module

Drop-down menu with the SITOP BAT1600, SITOP UPS1100

battery modules or third-party battery saved by the HSP.

Battery type

Pb / pPb

Typical ambient temperature

-70 … 100 °C

40 °C

Total capacity

0 - 3,200 Ah

10.0 Ah

End-of-charge voltage at 20 °C

24.0 - 30.0 V

27.3 V

Temperature coefficient

0 - 200 mV/K

36 mV/K

Battery constant voltage duration

0 - 720 h

12 h

Charge current

0.001 - 3 or 4 or 5 A

0.3 A

Start preserve charge voltage

23.0 - 30.0 V

25.2 V

Stop buffering voltage

18.0 - 23.0 V

18.5 V

Faulty battery voltage

1.0 - 18.0 V

6.0 V

Reset to initial values

•

Battery module

Type of SITOP BAT1600, SITOP UPS1100 battery modules or third-party battery

•

Battery type

Make/type of battery: Pb … lead-gel battery, pPb … pure lead battery

•

Typical ambient temperature

Typical ambient temperature of the battery in operation

•

Total capacity

Total capacity of the installed batteries.

•

End-of-charge voltage at 20 °C

The end-of-charge voltage defines the maximum battery voltage during the charging

phase. When reaching this end-of-charge voltage, the charging status changes from

"constant current" into the "constant voltage" phase. The adjustable end-of-charge voltage

is applicable for a battery ambient temperature of 20 °C. SITOP UPS1600 adapts the end-

of-charge voltage corresponding to the connected SITOP BAT1600 or SITOP UPS1100

depending on the battery ambient temperature and the battery technology. For third-

party batteries, the adaptation is based on configuration parameters battery type, typical

ambient temperature and temperature coefficient.

•

Temperature coefficient

Relative dependency of the end-of-charge voltage on the ambient temperature

•

Duration of the constant floating voltage charging phase

Duration of the constant voltage charging phase

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды

Siemens 6EP4131-0GB00-0AY0, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды