Siemens 6EP4131-0GB00-0AY0 Скачать руководство пользователя страница 195

Страница: 195 / 264

Mounting/removing

5.3 SITOP UPS1100

SITOP UPS1600 / BAT1600 / UPS1100
Equipment Manual, 07.2021, A5E37775406-11-76

195

5.3

SITOP UPS1100

WARNING

Installing the device in a housing or a control cabinet

The SITOP UPS1100 battery modules are built-in units. They must be installed in a housing

or control cabinet where only qualified personnel have access.

All devices are suitable for direct wall mounting.

Devices 6EP4131-0GB00-0AY0 (1.2 Ah), 6EP4132-0GB00-0AY0 (2.5 Ah), 6EP4133-0GB00-

0AY0 (3.2 Ah) and 6EP4133-0JB00-0AY0 (5 Ah) can also be snapped onto a DIN rail TH35×15

(EN 60715), and device 6EP4131-0GB00-0AY0 (1.2 Ah) also onto a DIN rail TH35×7.5

(EN 60715).
The lower part of the control cabinet or the coolest location in the control cabinet should be

chosen as mounting location.

WARNING

Use in hazardous zones

When the device is installed in a hazardous zone (II 3G nA IIC T4 Gc),

not permissible for

6EP4133-0JB00-0AY0 (5 Ah)

, then this must be installed in a distribution box with degree

of protection IP54 or higher. This distribution box must comply with the requirements of

EN 60079-15.

WARNING

In hazardous zones, it is not permissible that UPS1100 battery modules are connected in

parallel!

Mounting

See Chapter Dimensions and weight for the holes for wall mounting SITOP UPS1100

(Page 54).
To mount the device on a standard mounting rail, place it with the standard mounting rail

guide at the upper edge of the DIN rail and snap it in downwards. If this is too difficult, push

the device downwards while pressing on the rail as described for "Removal".

Note

The fuses should be inserted in the fuse holder only when commissioning the device

(charged batteries).

Содержание 6EP4131-0GB00-0AY0









































































































































































































































































Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды

Siemens 6EP4131-0GB00-0AY0, Руководство по эксплуатации оборудования

Результаты поиска

Содержание 6EP4131-0GB00-0AY0

Отзывы:

Похожие инструкции для 6EP4131-0GB00-0AY0

Бренды по названию

Популярные бренды