background image

 13

PJC211/212/221/222

     

2.0.2 - 2013

Cooling Signal Output

Values:  Normal (default)/Inverted

Set to Normal when using a hydraulic cooling pump.

Should be set to Inverted when using an electrical cooling pump with 

a 10 2380A-12/24V relay box

SETUP cont.

Cooling Power Save

Values:  ON (default)/OFF

ON sets the Cooling Pump into power save mode,which means the 

Cooling Pump output is dropping to 0 volt when the oil pressure is be-

low 10 bar for more than 10 seconds (Cooling Pump are turned OFF).

Tank Monitor

Values:  ON (default)/OFF

ON is when you have a tank monitor, oil level and Oil temp sensor. 

OFF is when you do not have a tank monitor and the display will show 

0°C and no alarm for high temperature or low level will not be trans-

mitted on the S-link.

Instance

Values:  --(default)/PORT/STARBOARD

Setting the PHC024 tank controller instance. For a mono hull boat

the instance should be ”--“.  If you have an catamaran with two 

PHC024 controllers then the one in the port hull should be set as

“PORT” and the one in the starboard hull as “STARBOARD”. This 

way the two controllers are shown in the panel display as two 

different oil tanks to monitor.                          

Main Switch

Press the button below 

 to return to the previous menu.

Press the button below 

 to edit the selected parameter.

Parameter value will start to blink, use joystick to alter value. 

Press the button below 

 to save edited parameter to device

Press the button below 

 to cancel editing without saving.

Location

Values:  BOW/STERN/BOW-STB/STERN-STB

Set the location for selected device. Use BOW or STERN in a conven-

tional thruster system. In a system with two bow or stern thrusters 

(i.e a catamaran), use BOW or STERN for port thruster, BOW-STB or 

STERN-STB for starboard thruster 

Cooling Pump 

Values:  Always Running/Temp Controlled(default)

When the option “Temp Controlled” is selected, the cooling pump will 

start when oil temperature exceeds 50°C and stop when the oil tem-

perature goes below 40°C.

On systems with two oil tanks, this setting will apply to both tanks.

                              

Содержание S-link PJC-212

























Отзывы: