Sicotec SLC TWIN RT2 LION Скачать руководство пользователя страница 39

Страница: 39 / 48

Operating mode / state

Battery test

Description.

With the UPS in AC mode or CF mode, press the ‘TEST

’

button for more than 0.5 seconds. The audible alarm will beep and the battery test

will start. In the electric flow diagram of the display, the line between I / P and the inverter icon flashes for information purposes. This test

is useful to check the battery state.

LCD display.

Error or fault

state

TWIN RT2

4-10kVA

When an error or fault is detected in the UPS, the inverter will lock. The fault code will be displayed on the screen and the

icon will

illuminate. Table 13 shows the error or fault codes and the correlation with the description.

BYPASS

Tab. 19.

Operating modes.

7.3.4.3. Warning or alert codes.

Code

Warning or alert description

Disconnected battery.

Overcharge in the battery.

Low battery.

Output overload.

Fan fault.

EPO activated.

Overtemperature.

Charger fault.

L1 input fuse open.

Line voltages of UPSs connected in parallel are different

Bypass voltages of UPSs connected in parallel are different

UPS locked in bypass after 3 successive overloads in 30 minutes

Maintenance switch cover open

Bypass not available

Start-up fault

Tab. 20.

Warning or alert code.

7.3.4.4. Error or fault codes.

Code

Error or fault description

DC bus start-up fault.

DC bus overvoltage.

DC bus undervoltage.

DC bus imbalance.

Inverter soft start fault

High voltage in the inverter

Low voltage in the inverter

Inverter output short-circuited

Negative power fault at the output.

Battery thyristor short-circuited.

Inverter relay short-circuited.

Battery charger short-circuited at its output

CAN communication fault

Parallel cable fault

Parallel communication fault

Overtemperature

CPU communication fault

Output overload

Battery start-up fault

PFC current fault in battery mode

DC Bus voltage change too fast

Tab. 21.

Error or fault code.

7.3.4.5. Warning or alert indicators.

Code

Icon (flashing)

Audible alarm

Battery voltage low.

Modulated every 1 seconds

Overload.

Modulated twice every 1

seconds

Disconnected battery.

BATT FAULT

Modulated every 1 seconds

Battery overcharge

Modulated every 1 seconds

EPO activated.

Modulated every 1 seconds

Fan fault /

Overtemperature

TEMP

Modulated every 1 seconds

Charger fault

CHARGING

BATTERY

Modulated every 1 seconds

Tab. 22.

Warning or alert indicators.

USER MANUAL

Содержание SLC TWIN RT2 LION

















































Результаты поиска

Содержание SLC TWIN RT2 LION

Отзывы:

Похожие инструкции для SLC TWIN RT2 LION

Бренды по названию

Популярные бренды

Sicotec SLC TWIN RT2 LION, Руководство пользователя

Результаты поиска

Содержание SLC TWIN RT2 LION

Отзывы:

Похожие инструкции для SLC TWIN RT2 LION

Бренды по названию

Популярные бренды