background image

34

7.3.  CONTROL PANEL FOR 4 KVA TO 10 KVA MODELS.

 

The control panel consists of:

 

ˆ

Four buttons with the functions described in Tab. 15.

 

ˆ

A backlit LCD display.

 

ˆ

Four optical LEDS (see Tab. 17).

BYPASS

LINE

BATTERY

FAULT

OFF/ESC

TEST/

MUTE/

ON/

Fig. 25. 

View of the control panel.

Button

Description

OFF/ESC

- UPS shutdown.

Press this button for at least 2 seconds.

- ESC functionality.

Press this button to return to the last parameter of the 

settings or configuration menu.

TEST/

- Activating the battery test.

Press this button for 3 seconds while in normal or frequency 

converter (CF) mode. At the end of the test, it returns to the 

respective mode.

- Button to navigate upwards.

When this button is pressed in UPS settings mode, it will 

move through the menu structure to the following variable 

in relation to the point where it is located.

MUTE/

- Muting the alarm.

Press the button for at least 3 seconds to mute or unmute 

the audible alarm.

It is only possible to mute the battery discharge and bypass 

alarm.

- Button to navigate downwards.

When this button is pressed in UPS settings mode, it will 

move through the menu structure to the previous variable in 

relation to the point where it is located.

ON/ 

- Starting up the UPS.

Press the button for at least 2 seconds.

- Confirmation of selection.

Press this button to confirm selection in the device’s settings 

mode.

TEST/

 + 

MUTE/

Press and hold the two buttons simultaneously for more than 

1 second to enter / exit the settings or configuration menu.

 (CF) 

Working mode of the UPS as a frequency converter, 

in the static bypass it is disabled.

Tab. 15. 

Functionality of the control panel buttons.

7.3.1.  Audible alarms.

Description

Alarm modulation or tone

Possibility of 

muting

State of the UPS

Bypass mode

Beep every 2 minutes.

Yes

Battery mode

Beep every 4 seconds.

Fault

Continuous.

Warning

Overload

2 beeps every second.

Yes

Other

Beep every 1 seconds.

Faults

All

Continuous.

Yes

Tab. 16. 

Audible alarms.

7.3.2.  Optical indications.

State of the UPS

LEDs

Bypass 

(yellow)

Line 

(green)

Battery 

(yellow)

Fault 

(red)

UPS start-up

No output mode

Bypass mode

AC mode

Battery mode

CF mode

ECO mode

Battery test

Fault

:  LED illuminated permanently. 

: LED off.

Tab. 17. 

Interaction between optical LEDs for the different 

modes or states of the UPS.

7.3.3.  Location of the adjustment parameters on the display.

Parameter 1

Parameter 2

Parameter 3

Fig. 26. 

Arrangement of the parameters on the LCD display.

 

 

 
 
 
 
 
 
 
 

 

 

 
 
 
 
 
 
 
 

Содержание SLC TWIN RT2 LION

















































Отзывы: