SICK sBot Stop Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 60

background image

7

Configuration

Configuration of the safety controller

The safety controller is configured by means of a rotary switch on the main module.

For further information on configuration and start sequence,

see "Configuring the Flexi

Classic safety controller", page 41

and see operating instructions for the Flexi Classic

safety controller.

Configuring the safety laser scanners

Depending on model, the safety laser scanners are configured using the Safety
Designer software or the CDS (Configuration & Diagnostic Software). For further infor‐
mation on configuration,

see "Configuring the safety laser scanner", page 42

operating instructions of the respective safety laser scanner.

Safety laser scanner

Configuration software

S300 Mini Standard

CDS (Configuration & Diagnostic Software)

microScan3 Core I/O

Safety Designer

S3000 Standard

CDS (Configuration & Diagnostic Software)

7.1

Requirements for software and firmware

Configuration of the safety laser scanner in this safety system requires at least the fol‐
lowing versions of the software or firmware:

Table 20: Minimum versions

Software and firmware

Minimum version

Safety Designer

1.2

CDS (Configuration & Diagnostic Software)

3.7.2

The software can be downloaded at

7.2

Additional configuration required

7.2.1

Configuring the Flexi Classic safety controller

The Flexi Classic safety controller is configured by means of a rotary switch. A screw‐
driver is required for this.

CAUTION

If a change is made to the configuration, the protective device must be checked to
ensure that it is effective. For this purpose, the test instructions in the operating instruc‐
tions of the respective component must be observed.

1.

Switch off the voltage supply at all main modules (terminals A1 and A2).

2.

Using a screwdriver, set the desired switch settings (programs and functions) at
the rotary switches on all modules.

3.

Set the control functions through external wiring of terminals S1, S2 and S3 on all
modules.

4.

Switch on the voltage supply of all modules while pressing the Enter pushbutton of
the main module.

NOTICE

Do not press any of the connected reset pushbuttons when doing this.

CONFIGURATION

7

8023421/12KF/2019-01-22 | SICK

O P E R A T I N G I N S T R U C T I O N S | sBot Stop

41

Subject to change without notice

«
...
39
40
41
42
43
...
»

Содержание sBot Stop





























































Отзывы:

Нет отзывов

Похожие инструкции для sBot Stop

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGS Страницы: 5

Бренд: HAGER WERKEN Страницы: 2

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Olympus Страницы: 56

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренд: Raymarine Страницы: 38

hsb2 PLUS Series

Бренд: Raymarine Страницы: 248

Бренд: Mach Страницы: 12

Бренд: V-TAC Страницы: 13

Бренд: Vari Lite Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды