SICK sBot Stop Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 60

background image

5.

When the ERR display starts to flash, release the Enter pushbutton again within
3 seconds.

✓

The selected operating mode is stored as a non-volatile setting and is active.

NOTE

If the Enter pushbutton is pressed for longer than 3 seconds, the entire system will
change to error status. The ERR display flashes.
All subsequent changes to the wiring at S1, S2 or S3 will lead to lock-out (ERR).

7.2.2

Configuring the safety laser scanner

NOTE

A protective field must be configured in the safety laser scanner which acts on the
OSSDs connected to the Flexi Classic safety controller.

7.2.2.1

Configuring the S300 Mini Standard

The S300 Mini Standard is configured with the CDS (Configuration & Diagnostic Soft‐
ware).

For configuration, refer to the S300 Mini Standard operating instructions.

NOTE

The resolution must be set in accordance with the risk assessment and the height of
the scan plane. For recommended values,

see "Mounting the safety laser scanner",

.

NOTE

The height of the scan plane must be checked,

see "Mounting the safety laser scan‐

.

Configuring the protective field

Figure 16: S300 Mini Standard configuration view (example)

7

CONFIGURATION

42

O P E R A T I N G I N S T R U C T I O N S | sBot Stop

8023421/12KF/2019-01-22 | SICK

Subject to change without notice

«
...
40
41
42
43
44
...
»

Содержание sBot Stop





























































Отзывы:

Нет отзывов

Похожие инструкции для sBot Stop

Бренд: Backyard Play Systems Страницы: 54

Бренд: MAHLE Страницы: 21

Бренд: Warehouse-lighting Страницы: 3

Бренд: Eagle Group Страницы: 8

Бренд: E2S Страницы: 5

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: Tar River Страницы: 44

Бренд: Tar River Страницы: 61

Бренд: Sabo Страницы: 76

Бренд: stilum Страницы: 4

Бренд: Dräger Medical Страницы: 92

Бренд: Gfp Страницы: 14

Бренд: SUHNER MACHINING Страницы: 30

Бренд: Eurotops Страницы: 8

Бренд: KRATOS SAFETY Страницы: 36

Бренд: Conductix-Wampfler Страницы: 12

Flumen OPTI-TR 22

Бренд: Wilo Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды