SICK sBot Stop Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 60

background image

•

Carry out a complete check of the safety functions of each system in every operat‐
ing mode. Carry out fault simulation. Monitor the response times of the applica‐
tion.

•

Document all configurations on the system, the connected devices and the safety
check.

In addition, the requirements of the thorough check before initial commissioning of the
components must be met:

•

deTec4 Core (8014253)

•

deTem4 Core (8020453)

•

microScan3 Core I/O (8016346)

•

S300 Mini Standard (8014170)

•

S3000 Standard (8009791)

Emergency stop pushbutton test

Mechanical operational check

•

The Emergency stop pushbutton is mounted so that it cannot be twisted.

•

The mounting nut tightened so that no play is possible in the longitudinal direction.

Electrical operational check

1.

Start the machine.

2.

Actuate the emergency stop pushbutton.

3.

Carry out a thorough check of the machine stop to make sure that the machine
has come to a stop due to operation of the emergency stop pushbutton.

16.2

Requirements for automated restart

NOTE

The following checklist only applies to this specific safety system and no claim is made
for completeness.
Pursuant to the manufacturer’s risk assessment, additional requirements may be nec‐
essary.

Table 40: Checklist for the manufacturer

Requirements

It is not possible to enter the hazardous area without interrupting the protective
field of the primary protective device.

Yes

⃞

No

⃞

It is not possible to walk behind the protective field of the safety laser scanner.

Yes

⃞

No

⃞

It is ensured that no people are in the hazardous area during or after the reset.

Yes

⃞

No

⃞

The hazardous area can only be entered when passing through the protective
field of the primary protective device and the safety laser scanner.

Yes

⃞

No

⃞

Appropriate measures have been taken to protect people within the hazardous
area (fence, screen, etc.) or to provide monitoring activities (protective device).

Yes

⃞

No

⃞

Additional protective measures (fence, screen, etc.) are installed in such a way
as to prevent their removal or manipulation.

Yes

⃞

No

⃞

Protective devices are secured against manipulation.

Yes

⃞

No

⃞

Protective devices are installed in such a way that it is not possible to stand
behind them, bypass them or crawl beneath them.

Yes

⃞

No

⃞

Guards are installed to provide the required minimum distance to the nearest
point in the hazardous area.

Yes

⃞

No

⃞

Necessary additional measures

16

ANNEX

58

O P E R A T I N G I N S T R U C T I O N S | sBot Stop

8023421/12KF/2019-01-22 | SICK

Subject to change without notice

«
...
56
57
58
59
60
»

Содержание sBot Stop





























































Отзывы:

Нет отзывов

Похожие инструкции для sBot Stop

Бренд: Keithley Страницы: 149

Бренд: JB-Lighting Страницы: 60

LOUDEN 200 Series

Бренд: ACCO Brands Страницы: 144

Бренд: B&K Страницы: 16

Бренд: B&G Страницы: 2

Бренд: Bang & Olufsen Страницы: 2

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: PASCO Страницы: 30

Бренд: Tascam Страницы: 78

MINISTUDIO CREATOR US-42

Бренд: Tascam Страницы: 11

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 11

Бренд: Daavlin Страницы: 55

Бренд: Daavlin Страницы: 19

Бренд: Tripp Lite Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды