SICK D 35 Series Скачать руководство пользователя страница 32

Страница: 32 / 68

Commissioning

8.1.3

Teaching in the background (ObSB)

Object between Sensor and Back

ground (ObSB)

The output is set when objects are detected that differ from the back

ground. The tolerance range around the taught-in background is

25 mm

plus a hysteresis of 25 mm. The hysteresis can be configured only via

IO-Link.

Dx
35

Min

Max

Fig. 14: Teaching in object between sensor and background (ObSB)

Teach point, position

Tolerance around teach point: ± 25 mm

Example: ObSB mode is to be set for the Q1 switching output.
1. Align distance sensor on background (teach point

2. Press the

select

pushbutton for longer than 5 seconds. The LED

near

lights up.

3. Keep pressing the

select

pushbutton until the LEDs

near

and

far (ObSB)

light up.

4. Press the

set

pushbutton.

If the teach was successful, the setting is applied immediately. The

LEDs

and

flash twice simultaneously. If the teach was not suc

cessful, the LEDs

and

flash alternately.

If necessary, perform fine teach.

→

See Chapter 8.3 on page 34

6. In order to leave teach mode, either press the

select

pushbutton

longer than 5 seconds or wait 5 minutes without pushing the pushbut-

tons.

Содержание D 35 Series





































































Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды

SICK D 35 Series, Руководство по эксплуатации

Результаты поиска

Содержание D 35 Series

Отзывы:

Похожие инструкции для D 35 Series

Бренды по названию

Популярные бренды