Shinko AER-101-ORP Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 84

background image

65

Standard Functions

Adjustment Mode

For successful measurement of ORP, ORP value in the
sensor location, electrode performance and standard
solution accuracy respectively play an important role for
obtaining reliable data.
By setting the adjustment value, calibrates ORP value
indicated on the AER-101-ORP to read 260 mV (at 20 )
when immersing the ORP Combined Electrode Sensor in
the standard solution (Quinhydrone potential difference 260
mV).

Span Sensitivity
Correction Mode

By setting the Span sensitivity correction value in
percentage, calibrates ORP value indicated on the
AER-101-ORP to read 260 mV (at 20 ) when immersing
the ORP Combined Electrode Sensor in the standard
solution (Quinhydrone potential difference 260 mV).

EVT Output

Setting Accuracy

Same as indication accuracy

Output Action

P control: When setting proportional band to any value

other than 0.

ON/OFF control: When setting proportional band to 0.

EVT

proportional band

0 to 4000 mV

EVT

proportional cycle

1 to 300 sec.

EVT

ON side, OFF side

0 to 200 mV

EVT

output high, low limit

0 to 100%

Type

Selectable by the keypad from the following.
• No action
• ORP input low limit action
• ORP input high limit action
• Cleansing output
• ORP input error alarm output

Output

Relay contact 1a

Control
capacity

3 A 250 V AC (resistive load)
1 A 250 V AC (inductive load, cos =0.4)

Electrical life

100,000 cycles

EVT ON Delay
Time

0 to 10000 sec.

EVT OFF Delay
Time

0 to 10000 sec.

Output ON Time/
OFF Time

when

EVT Output ON

If ON time and OFF time are set, the output will be turned
ON/OFF at constant intervals when EVT output is ON.

«
...
63
64
65
66
67
...
»

Содержание AER-101-ORP





















































































Отзывы:

Нет отзывов

Похожие инструкции для AER-101-ORP

Бренд: A&D Страницы: 74

Бренд: jablotron Страницы: 2

Stage Piano MP8

Бренд: Kawai Страницы: 70

Electone Stagea ELS-01C

Бренд: Yamaha Страницы: 248

TEMS AUTOMATIC - 2

Бренд: ASCOM Страницы: 12

Бренд: Endress+Hauser Страницы: 24

Бренд: Hanna Instruments Страницы: 28

Бренд: SMPE Страницы: 2

Бренд: Chauvin Arnoux Страницы: 12

Бренд: Bluther Страницы: 24

28APE190008/AI481

Бренд: Apera Instruments Страницы: 13

Бренд: CESVA Страницы: 9

Бренд: Hygrodynamics Страницы: 20

Бренд: Kusam-meco Страницы: 4

Бренд: Capintec Страницы: 49

Бренд: CATH-TECH Страницы: 48

Бренд: PCB Piezotronics Страницы: 10

Бренд: BERTHOLD TECHNOLOGIES Страницы: 127

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды