Shinko AER-101-ORP Скачать руководство пользователя страница 26

Страница: 26 / 84

Character

Setting Item, Function, Setting Range

Factory Default

Output OFF time when EVT1 output ON

0 sec.

• Sets Output OFF time when EVT1 output is ON.

If ON time and OFF time are set, EVT1 output can be turned ON/OFF
in a configured cycle when EVT1 output is turned ON.(Fig. 7.3-2, p.28)

• Available when

(ORP input low limit action) or

(ORP input high limit action) is selected in [EVT1 type].

• Not available for P control action
• Setting range: 0 to 10000 sec.

EVT1 ORP input error alarm EVT

type

No action

• Selects EVT

output type (except EVT1 type) in order to assess

EVT1 ORP input error alarm.

• Available only when

(ORP input error alarm output) is

selected in [EVT1 type]

•

: No action
: EVT2 action
: EVT3 action
: EVT4 action

EVT1 ORP input error alarm span
when EVT

output ON

0 mV

• Sets span to assess EVT1 ORP input error alarm when EVT

output

(selected in [EVT1 ORP input error alarm EVT

type]) is ON.

• Available only when

(ORP input error alarm output) is

selected in [EVT1 type]

• Setting range: 0 to 2000 mV

When set to 0 (zero), ORP input error alarm is disabled.

EVT1 ORP input error alarm time
when EVT

output ON

0 sec.

• Sets time to assess EVT1 ORP input error alarm when EVT

output

(selected in [EVT1 ORP input error alarm EVT

type]) is ON.

• Available only when

(ORP input error alarm output) is

selected in [EVT1 type]

• Setting range: 0 to 10000 seconds or minutes

(*)

When set to 0 (zero), ORP input error alarm is disabled.

(*) Time unit follows the selection in [ORP input error alarm time unit].

Содержание AER-101-ORP





















































































Результаты поиска

Содержание AER-101-ORP

Отзывы:

Похожие инструкции для AER-101-ORP

Бренды по названию

Популярные бренды

Shinko AER-101-ORP, Инструкция по эксплуатации

Результаты поиска

Содержание AER-101-ORP

Отзывы:

Похожие инструкции для AER-101-ORP

Бренды по названию

Популярные бренды