Sharp MD-X7H, Руководство по обслуживанию

Страница: 59 / 148

– 23 –
MD-X8H
Step 18 Press once the CD PLAY button. TCRS comparison level 1 for high reflection [ T C R S C 1 P _ ]
Step 19 Press once the CD PLAY button. Comparison level in case of COUT generation (playback) [ C O T L V P _ ]
Step 20 Press once the CD PLAY button. Comparison level in case of COUT generation (pecord) [ C O T L V r _ ]
Step 21 Press once the CD PLAY button. Auto-move waiting time setting [ W A I T m_ _ _ ]
Step No. Setting Method Remarks Display
d) Slide setting
Step 1 Testmode STOP state [ t s m e ]
Step 2 Press the CD PLAY button seven times. EEPROM setting menu [E E P R O M _ S E T]
Step 3 Press once the MD PLAY button. Focus setting menu [ _ _ F o c u s _ _ _ ]
Step 4 Press the CD PLAY button three times. Slide setting menu [ _ _ _ S l e d _ _ _ ]
Step 5 Press once the MD PLAY button. Slide system loop filter gain constant setting [ S L G _ _ _ _ _ ]
Step 6 Press once the CD PLAY button. Slide system loop filter f characteristic constant 2 setting [ S L 2 _ _ _ _ _ ]
Step 7 Press once the CD PLAY button. Slide output limitter setting [ S L D L I M _ _ ]
Step 8 Press once the CD PLAY button. Slide servo output dead zone level setting [ S L D L E V _ _ ]
Step 9 Press once the CD PLAY button. Slide kick pulse level setting (forced move) [ S L K L V k _ _ ]
Step 10 Press once the CD PLAY button. Slide kick pulse level setting (for 10 lines jump auxiliary use) [ S L K L V t _ _ ]
Step 11 Press once the CD PLAY button. Slide kick pulse level setting (move) [ S L K L V m _ _ ]
Step No. Setting Method Remarks Display
• : Setting volue
• Pressing the REC button causes reversing.
• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.
• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.
• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.
• : Setting volue
• Pressing the REC button causes reversing.
• If the VOL UP button is pressed while the specific setting item is indicated, the setting increases, and the new setting is set in LSI.
• If the VOL DOWN button is pressed while the specific setting item is indicated, the setting decreases, and the new setting is set in LSI.
• If the VOL UP/VOL DOWN button is held down, the setting changes continuously with 100 ms cycle.
Temperature measurement value correction table
Ambient temperature
correction
+ 12.2
°
C ~ + 15.8
°
C -0 3
H
+ 15.9
°
C ~ + 19.6
°
C -0 2
H
+ 19.7
°
C ~ + 23.2
°
C -0 1
H
+ 23.2
°
C ~ + 26.8
°
C
±
0
H
+ 26.9
°
C ~ + 30.7
°
C +0 1
H
+ 30.8
°
C ~ + 34.3
°
C +0 2
H
+ 34.4
°
C ~ + 37.9
°
C +0 3
H
EEPROM record value = Microcomputer measurement value +
Correction
*
EEPROM record value
Value to be measured by the microcomputer at +25
°
C
* Microcomputer measurement value
Value to be measured by the microcomputer at specific
temperature
* Correction value
Correction value for conversion to measurement value at
+25
°
C (see the table shown left)
Note
1. Do without mechanical connection.
2. Do immediately after turning on the power.
Ambient temperature
temperature code
+ 19.6
°
C ~ + 30.7
°
C 0 6
+ 8.7
°
C ~ + 19.6
°
C 0 7
• Temperature code check
The temperature code is read after automatic adjustment. If it is within the range shown below, the adjustment is OK.