Sharp FO-4500, Руководство по обслуживанию

Страница: 46 / 192

SW4 No. 1 ~ No. 3 Communication results printout
It is possible to obtain communication results after each transaction.
Normally, the switch is set (No. 1: 0, No. 2: 0, No. 3: 1) so that the
communication result is produced only a communication error is en-
countered. If No. 1 was set to 1, No. 2 was set to 1 and No. 3 was set
to 0, the communication result will be produced every time a commu-
nication is done, even if the communication was successful.
If No. 1 was set to 0, No. 2 to 1 and No. 3 to 0, the communication
result will be produced every transmission.
Setting No. 1 to 1 No. 2 to 0 and No. 3 to 0 will disable this function.
No transaction report will be printed.
If No. 1 was set to 0, No. 2 to 0 and No. 3 to 0, the communication
result is produced only after a timer and memory transmission or
when a communication error is encountered.
SW4 No. 4 Image addition function to the communication result
table (for memory transmission only)
Used to set addition of sending image to the communication result
table.
SW4 No. 5, No. 6 Reserved
Set to "0".
SW4 No. 7 Reserved
Set to "1".
SW4 No. 8 Multi-TTI feature
When this switch is set to "1", Multi TTI function is enabled.
SW5 No. 1 Time display format
When this switch is set to "0", time is displayed in 12-hour system.
When set to "1", 24-hour system.
SW5 No. 2 Date display format
Used to select date display/print formats.
SW5 No. 3 Header print
When it is set at 0, sender’s name, sending page number and so on
are automatically printed in the recording paper on the receiving side
during transmission. Thus, the sender can be known on the receiving
side.
0: Applied.
1: Not applied.
SW5 No. 4 Footer print
When set to "1", the date of reception, the sender machine No., and
the page No. are automatically recorded at the end of reception.
SW5 No. 5 Relay data output
0: Output ON
1: Output OFF
SW5 No. 6 Substitute reception
Selection of substitute reception in the case of recording paper ex-
hausted or paper jam. If set to "NO", auto receive is disabled even
when the receive memory is ready to receive.
Substitute reception is not performed even during receive operation.
SW5 No. 7 Substitute reception condition
Selection of substitute reception according to existence of TEL num-
ber from transmitting side. Initial setting allows substitute reception
without CSI. If set to "no", the receiver cannot receive any documents.
SW5 No. 8 CSI transmission
CSI signal contains the sender’s phone number registered in the ma-
chine. If this switch is set to "1", no sender’s name will be printed at
the receiving side.
SW6 No. 1 MH fixed
Normally set to allow automatic selection of MH and MR mode ac-
cording to the remote side.
If set to 1, the mode is fixed to MH and is useful if the remote side is a
MH only unit; or a lot of image distortion is met due to a bad line.
SW6 No. 2 H2 mode
Used to determine H2 mode (15 sec transmission mode). When set to
OFF, H2 mode is inhibited even though the transmitting machine has
H2 mode.
SW6 No. 3 Reserved
Set to "0".
SW6 No. 4 ~ No. 8 Modem speed (DCS date reception speed)
Used to determine the initial modem speed. The default is 14400BPS
(V17). It may be necessary to program it to a slower speed when
frequent line fallback is encountered, in order to save the time re-
quired for the fallback procedure.
SW7 No. 1, No. 2 Reception speed fixed
The transferable speed of modem in the receiving mode is set.
SW7 No. 3 DIS receive acknowledge during G3 transmission
Used to make a choice of whether reception of NSF (DIS) is acknowl-
edged after receiving two NSFs (DISs) or receiving one NSF (two
DISs).
It may be useful for overseas communication to avoid an echo sup-
pression problem, if set to 1.
SW7 No. 4 Non-modulated carrier in V29 transmission mode
Though transmission of a non-modulated carrier is not required for
transmission by the V29 modem according to the CCITT Recommen-
dation, it may be permitted to send a non-modulated carrier before the
image signal to avoid an echo suppression problem.
It may be useful for overseas communication to avoid an echo sup-
pression problem, if set to 1.
SW7 No. 5 EOL detection timer
Used to make a choice of whether to use the 25-second or 5-second
timer for detection of End of line.
This is effective to override communication failures with some facsim-
ile models that have longer End of line detection.
SW7 No. 6 Protocol monitor
Normally set to "0". If set to "1", communication can be checked, in
case of troubles, without using a G3 tester or other tools.
When communication FSK data transmission or reception is made,
the data is taken into the buffer. When communication is finished, the
data analyzed and printed out. When data is received with the line
monitor (SW4-No. 8) set to "1" the reception level is also printed out.
SW7 No. 7 Line monitor
Normally set to "0". If set to "1", the transmission speed and the
reception level are displayed on the LCD. Used for line tests.
SW7 No. 8 Max. length for TX/RX/Copy
Used to set the maximum page length.
To avoid possible paper jam, the page length is normally limited to
432 mm for copy or transmit, and 1.5 meters for receive.
It is possible to set it to "No limit" to transmit/receive a long document,
such as a computer print form, etc. (In this case, the receiver/transmit-
ter must also be set to no limit.)
FO-4500H
2 – 30