Sharp FO-4500, Руководство по обслуживанию

Страница: 45 / 192

SW2-No.3 ECM MODE 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
SW6-No.1 MH FIXED 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1
Compre-
ssion
method
ECM MMR mode Yes No Yes No No No No No No No No No No No No No
ECM MR mode Yes No Yes No Yes No Yes No No No No No No No No No
ECM MMH mode Yes Yes No No Yes Yes No No No No No No No No No No
ECM MH mode Yes Yes Yes Yes Yes Yes Yes Yes No No No No No No No No
MR mode Yes No Yes No Yes No Yes No Yes No Yes No Yes No Yes No
MH mode Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes
(Depending on remote machine)
•
Soft switch function description
SW1 No. 1 ~ No. 4 Recall interval
Choice is made for a recall interval for speed and rapid dial-numbers.
Use a binary number to program this. If set to 0 accidentally, 1 will be
assumed.
SW1 No. 5 ~ No. 8 Recall attempts
Choice is made as to how many recall attempts should be made. Use
a binary number to program this.
SW2 No. 1 Dialing mode
Switch the type according to the telephone circuit connected to the
facsimile.
0: PULSE DIAL
1: TONE DIAL
SW2 No. 2 Receive mode
Auto/manual receiving mode is set.
SW2 No. 3 ECM mode
Used to determine ECM mode function. Refer to the following table.
SW2 No. 4 Reserved
Set to "0".
SW2 No. 5 Polling security
This switch is employed to enable or disable the polling operation
using the ID code verification function, in order to prevent unautho-
rized polling operation.
SW2 No. 6 Auto cover sheet
When "1" (=YES) is selected, the cover sheet is automatically sent
after transmission of the original to notify the receiver of the number
of original sheets transmitted.
SW2 No. 7 JNNK-FAX function in manual reception
It is set whether JUNK-FAX is functioned in the manual receiving
mode or not.
SW2 No. 8 JUNK-FAX function
This function is used to receive data from a specific remote machine
(station registered in entry mode). It is the function that refused a
reception in the case that TSI of remote machine matched with fax
number of the station registered.
0: No
1: Yes
SW3 No. 1 ~ No. 4 Number of rings for auto-receive
(0: No ring receive)
When the machine is set in the auto receive mode, the number of
rings before answering can be selected. It may be set from one to
nine rings using a binary number. If the soft switch was set to 1, a
direct connection is made to the facsimile. If a facsimile. If it was set
to 0 accidentally, receive ring is set to 1. If it was above 9, receive
rings are set to 9. So, this has to be corrected.
SW3 No. 5 ~ No. 8 Switch to auto-receive from manual receive
(0: No switch)
Choice is made after how many rings in the manual receive mode it
should be automatically change to auto answer mode or remain in the
manual receive mode. Entering the binary number 0 forces the ma-
chine to remain in the manual answer mode. If a number between 1
and 9 is entered, the machine will go into the answer mode after the
given number of rings. However, it can be used as an ordinary tele-
phone if the handset is taken off the hook before this programmed
number is finished. If entry of a number above 9 by accident, it will be
set to 9. In this case, it must be corrected to the proper number.
FO-4500H
2 – 29